Starting The Robotic Cleaner; Cleaning Cycle; Stopping Robotic Cleaner Operation; Pulling Cleaner Unit Out Of The Water - Norsup CYCLONE Serie Notice Originale

ROBOTIC POOL CLEANER TYPE CYCLONE

6.3. STARTING THE ROBOTIC CLEANER

Connect the power and control unit to the wall
socket (1). The Operation LED is lit (4) and the robotic
cleaner starts its cleaning program.
If the power and control unit is already connected to
the AC socket, the Operation LED flashes (5) to
indicate that the robotic cleaner is in standby mode.
Press the Operation button (6). The Operation LED
turns on (6) and the robotic cleaner starts
the cleaning program.
NOTE
When the Check Filter LED (3) (optional in some
models.) is lit, the robotic cleaner filters must be
cleaned before placing the cleaner unit in the pool.

6.4. CLEANING CYCLE

During the cleaning cycle, the robotic cleaner:
- Moves across the pool floor picking up dirt and debris.
- Changes direction and rotates automatically
according to the selected program.
- Climbs the pool walls every few minutes, as set in its
internal program.
NOTE
The robotic cleaner might occasionally stop
moving for a few seconds. This is part of normal
operation, not a malfunction.

6.5. STOPPING ROBOTIC CLEANER OPERATION

The robotic cleaner moves automatically to STANDBY
after every cleaning cycle and the operation LED
starts flashing (5).
To stop the cleaner operation during a cleaning cycle,
press the operation button (7) once. The operation LED
starts flushing (7) and the cleaner is in standby mode.

6.6. PULLING CLEANER UNIT OUT OF THE WATER

1. Unplug the floating cable from the power and
control unit.
2. Pull up on the floating cable to pull the cleaner
unit closer until it is possible to take hold of the
handle.
3. Using the handle, lift the cleaner unit out of the
pool.
CAUTION
Do not use the floating cable to lift the cleaner unit
out of the water.
10 WWW.NORSUP.EU
Alterations which serve the technological progress as well as errors excepted!
ROBOTIC POOL CLEANER TYPE CYCLONE

7. MAINTENANCE

7.1. CLEANING THE FILTERS

The two filters must be cleaned after each cleaning cycle.
1. Release the filter and pull it out of the cleaner unit. (1), (2)
2. Pull the filter door against the filter housing to
open the filter case. (3), (4)
3. Spray water on the outer sides of the filter and
then spray water towards the inner side of the filter
to clean all the dirt and debris. (5)
4. Verify that the small plastic shutter (2) is in place
and not broken, then close the filter. (6)
5. Insert the filter back into its location until a click is
heard to secure the filter in place.(7), (8)

7.2. STORING THE ROBOTIC CLEANER

Follow these instructions to store the robotic cleaner
when not in use:
1. Disconnect the power cord
from the wall outlet.
2. Disconnect the floating cable
from the power and control
unit.
3. Spread out the floating cable
and release any twists in the
cable.
4. Wash the cleaner unit interior
space with fresh water and let
it dry.
5. Roll the floating cable and
place it ON THE CLEANER
unit.
CAUTION
DO NOT ROLL the floating cable ON THE HANDLE
of the cleaner unit.
6. Store the robotic cleaner components in a dry,
closed location.
7. Verify that the power and control unit is not
exposed to water.

7.3. CHECKING WATER OUTLET PROPELLER

It is recommended to periodically clean debris
and hair from the propeller of the water outlet:
1. Remove the screws
(3) that holds water
outlet cover(2).
2. Remove the water
outlet cover (2).
3. Clean any hairs, dirt,
or debris.
4. Verify that the
propeller (1) is not
broken.
5. Return the cover (2)
and fasten it with
the screws (3).
Alterations which serve the technological progress as well as errors excepted!
EN
DE
FR
ORIGINAL MANUAL NORSUP 11