Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
x1 Canopy (A) x7 Support Stanchions (B1)
x5 Track Fixtures (E)
ASSEMBLY INSTRUCTIONS(AS SHOWN IN DIAGRAM):
CREATE LAYOUT
This line voltage flexible track kit allows you maximum flexibility in creating an attractive lighting system for your room. The track can be
mounted in an infinite combination of curves and straight runs. The power canopy and the multi-directional track heads can be mounted
anywhere along the track run. Layout the track in the approximate location to be installed.
STEP 1: INSTALL THE CANOPY(A)
1.
Turn off the main power.
2.
Install mounting bracket to existing outlet box with screws.
3.
Pull wires through mounting bracket.
A. Make ELECTRICAL CONNECTIONS: Connect the white wire(s) from the fixture to the white wire of the supply circuit. Connect the
black wire(s) from the fixture to the black wire of the supply circuit. Connect the green or bare copper wire to the ground wire of the
supply circuit. Use UL/CSA listed wire connectors suitable for the size type, and number of conductors. No loose strands or loose wires
should be present. Secure wire connectors with UL/CSA listed electrical tape.
B. Carefully tuck connected wires back into the outlet box.
4. Secure Outlet Box Canopy to the mounting bracket with the screws provided.
STEP 2: INSTALL CEILING SUPPORTS(B)
Method 1: Support stanchions(B1)
1.
Remove support stems from stanchions.
2.
Lay out your track design and mark the position for each stanchion. Evenly space stanchions so that they form desired pattern. (Use minimum 20" spacing
between stanchions when using 7 stanchions.)
3.
Drill holes in the ceiling at desired stanchion location by electrical drill. (Note: Please use diameter 6mm drill bit)
4.
Install enclosed screw anchors into drilled holes.
5.
Insert the stanchion screws to secure stanchions to the ceiling.
6.
Screw the support stems into the stanchions, and then install the track mounting brackets to the support stems as shown in the figure.
Method 2: Toggle bolts(B2)
1.
R
emove support stems from stanchions.
Lay out your track design and mark the position for each stanchion. Evenly space stanchions so that they form desired pattern. (Use minimum
20" spacing between stanchions when using 7 stanchio
3
Drill 5/8 inches (16mm) holes in the ceiling at desired stanchion location.
4.
Push toggle bolts into the holes drilled into the ceiling and tighten toggle bolts until the stanchion and decorative ring secured.
5.
Screw the support stems into the stanchions, and then install the track mounting brackets to the support stems as shown in the figure.
STEP 3: INSTALL TRACK(C)
1.
Remove the retaining cap on the power connector.
2.
Open the power connector cover and align the two slots of the track to the two tabs on the power connector.
3.
Close the power connector cover and replace the retaining cap making sure that the connection is secure.
4.
Remove the retaining cap, open the track mounting bracket, and then insert the flexible track into the track mounting bracket.
5.
Replace the retaining caps to secure the flexible track.
STEP 4: INSTALL FIXTURE(E)
1.
Remove the retaining caps from the fixtures.
2.
Align the two tabs of the track fixture adaptor to the two slots on the flexible track.
3.
Close the fixture adapters and replace the retaining caps making sure that the connection is secure.
STEP 5: RELAMPING THE BULB(F)
1. Make sure that the power is turned off.
2.
Make sure that the bulb is cool before re-lamping the fixture.
3.
Remove the decorative bulb retainer ring from the end of the fixture by turning counter clockwise.
4.
Remove and replace bulb as needed.
5.
Replace the decorative bulb retainer ring to the end of the fixture by turning clockwise.
6.
Restore electrical power.
CAUTION: Do not exceed the recommended maximum fixture wattage of 50 Watts
x7 Toggle bolts (B2)
Box
x1 Hardware Packet (G)
x1 10 Foot Flexible Track (C)
Publicité
Table des Matières
