Important Safety Instructions - HAMPTON BAY 535-675 Manuel D'instructions

Thank you for purchasing this Hampton Bay interior flexible track. This product has been manufactured with the highest standards of safety
and quality.
FEATURES:
1. Track can be shaped into various designs
2. Track heads are multi-directional
3. Can be used with a standard 120 Volt Incandescent style dimmer switch
4. Link Up to 4 Kits Together using 1 power supply
5. Power rating of up to 2400 watts.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU 535-675,UPC 008938100533, or SKU 725-367, UPC 008938102469 or SKU 904-270, UPC 008938268295.
GENERAL
1. Be sure to read these installation instructions and review the diagrams thoroughly before installing the track system.
2. All electrical connections must be in accordance with local codes and the National Electrical Code. If you are unfamiliar with methods of
installing electrical wiring, secure the services of a qualified licensed electrician.
3. This fixtures are intended to be mounted to a 4" square x 2-1/8"deep metal octagon outlet box. The box must be directly supported by the
building structure.
4. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box.
Turning the power off using the light switch is not sufficient to prevent electrical shock.
Note: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors that cannot be built into any product. These factors must be
supplied by the person(s) caring for, installing and operating the fixture. If at any time you are uncomfortable or are unsure of what to do,
please contact a qualified licensed electrician for further assistance.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before beginning the assembly or installation process. Save these instructions and refer to them when additions to or
changes in the track configuration are made.
1. For use with Hampton Bay EC series line voltage flexible track systems only.
2. This track system is designed for use with 120 volt circuits only.
3. The track system is not intended for use with a power supply cord, extension cords, etc. It is intended for direct wire to a junction box only.
4. Do not install this lighting system in damp or wet locations.
5. CAUTION – LIGHTED LAMP IS HOT! Keep away from curtains and other combustible materials. Do not touch lamp at any
time. Turn off power and allow bulbs to cool down before replacing. Use a soft cloth, gloves, or re-lamping tool (see diagram) to change
bulbs. Oil from skin may damage the bulb.
6. CAUTION – To reduce the risk of a burn during re-lamping, remove the track head from the track before re-lamping.
7. CAUTION: Do not touch hot lens, guard or enclosure.
8. Do not install any lamps closer than 6 inches (15cm) from any curtain or similar combustible material.
9. To prevent the risk of fire, do not conceal or extend the track through a wall or ceiling.
10. To prevent the risk of fire and electrical shorting, do not install in locations where it is possible for the electrical connections in
the track to make contact with any conductive metals.
11. To prevent the risk of fire and overheating, before turning the power on, make sure all connections are properly connected
and secure.
12. To prevent the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances, etc to the
track system.
13. Do not install any part of this system (TRACK) less than 7 feet (2.2m) above floor.
14. Turn the power off (breaker or fuse) before adding to, changing the configuration of the track, or modifying the light system in
anyway.
15. Use a minimum of 20" of space between stanchions when using 7 stanchions.
16. This flexible track kit is intended to be installed by support stanchions only.
17. Before energizing the fixture, make sure that the lighting system is clear of all material which could cause a direct short.
If at any time you are uncomfortable or are unsure of what to do, please contact a qualified licensed electrician for further assistance.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION(not included):
Ladder Safety goggles
Electrical tape
SAVE THESE INSTRUCTIONS
Wire stripper
Drill 1/4 In.(method 1) or 5/8 In.(method 2) Drill bits
Gloves Flathead screwdriver Phillips screwdriver