Double Monitor Mount With Gas Spring - Goobay 58531 Mode D'emploi

User Manual
EN

Double Monitor Mount with Gas Spring

1 Safety instructions
The user manual is part of the product and contains important information for cor-
rect use.
• Read the user manual completely and carefully before use.
The user manual must be available for uncertainties and passing the product.
• Keep this user manual.
• Do not modify product and accessories.
• Use product, product parts and accessories only in perfect condition.
• In case of questions, defects, mechanical damage, trouble and other problems,
non-recoverable by the documentation, contact your dealer or producer.
Not suitable for children and persons with physically and/or mentally limited abili-
ties.
• Secure packaging, small parts and insulation against accidental use.
• Mounting, dismounting, care, storage, transport and disposal may only be car-
ried out by users with basic mechanical knowledge.
• Have maintenance and repair work carried out by qualified personnel only.
• Avoid stresses such as heat and cold, moisture and direct sunlight vibration and
mechanical pressure.
• Place, install and transport product, product parts and accessories in a safe
way.
• When working with burdens, secure yourself and the working place, let a se-
cond person help you.
• Do not install the product to places with direct sunlight or bright light.
This contributes to eye fatigue.
• Do not hold limbs between shear parts during use.
Moving product parts can pinch or squeeze limbs.
• Keep enough space around product and to the whole system to ensure proper
ventilation and mobility.
• Compare the specifications of all products used.
The specifications of all used products must match or be within the specified range.
The supporting surfaces must be able to safely withstand the weight of the mount
and the equipment attached to it.
• Use the mounting screws provided.
• Do not over-tighten the screws.
Threads can be damaged.
2 Description and Function
2.1 Product
The product is a tiltable, rotatable and swivelling table monitor holder with gas pres-
sure spring for mounting two screens up to 9 kg each.
2.2 Scope of Delivery
See Tab. 1.
○ Spring arm with monitor mount (A)
○ Plate for screw clamp (B)
○ Screw clamp (C)
○ M6x12 (D)
○ M6x10 (E)
○ Insert (F)
○ Mounting screw (G)
○ Insert (H)
2.3 Required Tools
See Tab. 2.
○ Drill (1)
2.4 Specifications
Item No.
Screen size
Load capacity
Distance between threaded holes according to
VESA standard (vertical x horizontal)
Dimensions (width x max. height) / Weight
Tilt range
Swivel range / Rotation range
3 Intended Use
We do not permit using the device in other ways like described in
chapter „Description and Function" or in the „Safety Instructions". Use
the product only in dry interior rooms. Not attending to these regulations
and safety instructions might cause fatal accidents, injuries, and damages to
persons and property.
4 Preparation
• Check the scope of delivery for completeness and integrity.
Subject to change without notice.
Model similar.
○ Wing nut (I)
○ Allen key 4 mm (J)
○ Allen key 6 mm (K)
○ M4x12 (M-A)
○ M5x12 (M-B)
○ Washer D5 (M-C)
○ User Manual
○ Suitable drill bit (Ø 10,0 mm) (2)
58531
43 - 81 cm (17 - 32")
9 kg each
75x75, 100x100
117 x 498 mm / 4 kg
-45° ~ +70°
-180° ~ +180°
5 Mounting
5.1 Unpacking the spring arm with monitor mount
See Fig 1.
WARNING! Risk of injury from stored energy!
The spring arms are under pressure and can suddenly extend if released too qui-
ckly. Unpack the spring arms one by one.
1. Hold the spring arm fi rmly together on both sides and have another person cut
the cable tie around the spring arm.
2. Slowly release the pressure and let the spring arm extend gradually to its full
length.
5.2 Mounting on a table top
○ Preparation: See Fig. 2.
○ Table top 10-53 mm: See Fig. 3.
○ Table top 50-83 mm: See Fig. 4.
5.3 Mounting through a hole in the table
○ Preparation: See Fig. 5.
○ Tischplatte 10-83 mm: See Fig. 6.
5.4 Attaching the monitor mount to the screen
See Fig. 7.
This step must be carried out by 2 people!
5.5 Balancing the spring arm
See Fig. 8.
CAUTION! Material damage!
• Always keep the spring arm in a horizontal position when making adjustments.
If necessary, have another person help you.
The spring arm must be properly balanced after the screens have been attached.
Hold the spring arm in a horizontal position and adjust the spring tension with the
Allen key (K).
Do not overtighten the screws!
A If the spring arm sinks, turn the adjustment screw counterclockwise until it re-
mains in a horizontal position.
B If the spring arm rises, turn the adjustment screw clockwise until it remains in a
horizontal position.
5.6 Using the cable glands
See Fig. 9.
5.7 Adjusting the screen
See Fig. 10.
Set the desired angle and then tighten the screws alternately.
6 Maintenance, Care, Storage and Transport
• Let maintenance and repair work only be carried out by qualified personnel.
• Protect the joints from dirt and grease them regularly with light machine oil.
• Only use a dry and soft cloth for cleaning.
Use caution when cleaning to avoid scratches. In case of heavy soiling, the clea-
ning cloth can be slightly moistened with water.
• Do not use detergents or chemicals.
• Regularly check the tightness of product/screws.
Fixing holes can remain visible when the product is removed. After prolonged use,
a stain may remain on the underground.
• Store the product out the reach of children and in a dry and dust-protected am-
bience when not in use.
• Keep and use the original packaging for transport.
7 Disposal instructions
This product does not belong into the household waste. At the end of its working
life, give it back to the manufacturer, the sales outlet or established for this purpo-
se, public collection points for free. Details of disposal are regulated by the respec-
tive country's law. Recyclables are into the recycle circuit, in order to gain new raw
materials. The following recyclable materials are collected in municipal collection:
Waste glass, plastics, scrap metal, sheets and much more. With this type of scrap
usage you are making an important contribution to protecting our environment.
8 Warranty
Detailed warranty conditions on www.mygoobay.com.
9 Symbols used
For indoor use only
- 10 -
IEC 60417- 5957