Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
Motor Thermostat
IMPORTANT:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
•
Push the On/Off pedal once.
•
Disconnect the plug from the power
source.
•
Find the source of the overheating
problem. (i.e. clogged hose or dirty
filter)
TROUBLESHOOTING
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM
POSSIBLE CAUSE
1. Not properly plugged into wall
outlet.
Cleaner Won't
2. No electricity in wall outlet.
Run
3. On/Off pedal not turned on.
4. Motor thermostat tripped.
5. No power in electrical outlet.
1. Full or clogged dust cup.
2. Wrong pile height setting.
3. Clogged nozzle.
Cleaner Won't
4. Clogged dust inlet port.
Pick Up
5. Clogged hose.
6. Broken/ worn out belt.
7. Hose not inserted fully.
8. Dirty filters and filter frame
Cleaner Picks
Up Moveable
Rugs Or
1. Wrong pile height setting.
Pushes Too
Hard
Beater Brush
1. Broken/worn out belt.
Does Not Turn
2. Belt installed incorrectly.
Turbo Brush
1. Rotating brush or turbine
Does Not
obstructed.
Rotate Or
2. Belt broken.
3. Hose obstructed.
Rotates Slowly
1. Attachment use restricts air
Air Flow
flow.
Restricted With
2. New carpet debris clogging
Attachment Use
air path.
•
If clogged hose or dirty filter is
found, unclog the hose and/or clean
or replace the filter.
•
Wait at least 45 minutes before
attempting to reuse the vacuum.
•
After unit has cooled down for 45
minutes, plug in the cleaner and
press on the On/Off pedal. The
vacuum should start again. If the
vacuum still does not start, or if the
thermostat switches off the unit
again contact customer service at
1 (800) 798-7398.
POSSIBLE SOLUTION
1. Plug in firmly.
2. Check fuse or breaker.
3. Push On/Off pedal to turn on.
4. Reset motor thermostat.
5. Check fuse or breaker. Replace fuse or
reset breaker
1. Clean dust cup.
2. Adjust setting.
3. Remove obstruction.
4. Remove power nozzle base plate and
remove obstruction.
5. Remove obstruction.
6. Replace belt.
7. Push hose in securely at both ends.
8. Clean/change filters and filter frame.
1. Adjust setting.
1. Replace belt.
2. Check belt changing instructions.
1. Clear obstructions.
2. Call Customer Service.
3. Clear obstruction.
1. Check attachment.
2. Remove obstruction.
11
TO ORDER REPLACEMENT SUPPLIES
for Model V1504C
Call: 1 (800) 798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
visit our website: www.sharkclean.com
ITEM
Pre-Motor Filter
Drive Belt
FOR TECHNICAL SUPPORT
Call: 1 (800) 798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The dust cup screen and pre-motor filter are washable. We recommend washing
the pre-motor filter once every three months or when suction appears to be
reduced. DO NOT wash in the dishwasher.
The pre-motor filter should however be replaced once every year depending on the
amount of use, to ensure peak performance of your vacuum.
IMPORTANT:
Make sure that ALL washable filters and the pre-motor filter frame are completely
dry before inserting back in the vacuum. Allow the pre-motor filter and pre-motor
filter frame to air dry for 24 hours. DO NOT DRY IN THE DRYER.
or
PART #
XSH1504
XL1504
12
Publicité
Table des Matières
