Technical Data - MC Crypt A-1501 Mode D'emploi

• Capacitors in the device can still carry a charge even if the device has been disconnected
from all voltage sources.
Fuse replacement
Do not repair fuses or bridge the fuse holders.
If the fog machine is connected to the correct power source and the "ON / OFF" (I/O) button does
not light up when the machine is turned on, the fuse may be broken.Check the fuse and replace
if necessary.
1. Disconnect the fog machine from the power source.
2. Unscrew the FUSE cap using a Philip's head screwdriver of suitable size.
3. Check the fuse and replace it with a fuse of the same type if necessary.
Cleaning
Separate the device from the power supply and leave it to cool down before
cleaning.
• The device is maintenance-free. For this reason, you should never open it. If you do open the
device, the warranty will be rendered invalid.
• Clean it only with a soft, dry cloth or brush. Never use aggressive cleaning agents or chemical
solutions as the surface of the housing could be damaged.
• You can clean the outside of the fog machine with a damp cloth. Never use aggressive
cleaning agents or chemical solutions as the surface of the housing could be damaged.
• To avoid deposits and residues in the fog fluid channels, use a special fog machine cleaner.
Observe the instructions for the cleaning liquid.
7. Handling
• Never plug the power plug into a mains socket immediately after the device was taken from
a cold to a warm environment. The condensation water generated could destroy the product.
Allow the device to reach room temperature before connecting it. Wait until the condensation
water has evaporated.
• Never pull on the power cable. Only unplug it by pulling on the plug.
• Unplug the power supply if you do not use the device over a period of time.
• For safety reasons, always pull the mains plug from the socket during a thunderstorm.
• Never touch the device close to the fog output opening when it is in operation or shortly after
operation is stopped.
This part of the device becomes extremely hot. There is risk of burning.
• Never use dirty fog liquids. Always close the tank and the reservoir for your fog liquid right
after filling.
• Always empty the tank before transporting the device or not using it for a longer period.
• Only use water-based fog liquids. Suitable fog liquids are listed in the "Technical Data".
8. Troubleshooting
By purchasing this fog machine, you have acquired a product that has been designed according
to state of the art technology and that is operationally reliable. Nevertheless, problems or faults
may occur. We would therefore like to describe how you can eliminate certain malfunctions
yourself.
Please observe the safety instructions!
Suddenly there is no more fog production during operation:
• The device is re-heating. Once the heating process is complete, the device puts out fog again.
• The device is no longer connected to the voltage supply. Check the correct connection and
the voltage supplyof the outlet.
• The fuse has been triggered/blown. Change the fuse as described. Should the fuse trigger/
blow again, have the device repaired in a specialised workshop.
• The tank is empty and needs refilling.
The device continues to produce fog for a short period of time after it is switched off/unplugged:
• This is not a defect. The remaining fog liquid in the fog output opening is evaporating.
Repairs other than those described above should only be performed by an
authorised specialist.
9. Disposal
In order to preserve, protect and improve the quality of environment, protect human
health and utilise natural resources prudently and rationally, the user should return
unserviceable product to relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately
and not as municipal waste.

10. Technical data

Suitable fog liquid:
Suitable cleaning fluid:
Operating voltage:
Power conumption:
Initial warm-up time:
Continuous output smoke time (fully charged): 10 s ±3 s
Stop time between continuous fog ejection:
Discharge volume:
Discharge distance:
Tank capacity:
Colour:
Dimensions (W x H x D):
Weight:
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
Item no.: 590775 (1 l)
Item no.: 595900 (5 l, normal)
Item no.: 595918 (5 l, heavy)
Item no.: 590298 (1 l)
220 – 240 V/AC, 50 Hz
1350 W
approx. 4 minutes
20 s ±5 s
510 m /min
3
8 – 10 m
1.8 l
Black / silver
390 x 310 x 179 mm
6.5 kg
V2_0412_02-HL