Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
ICE CREAM TOPPING CABINET
MODELS ZR152, ZF152 and ZF071
Installation, Operation and
Maintenance Instructions
INSPECTION
When the equipment is received, all items should be checked against the bill of lading to
insure all crates and cartons have been received. All units should be inspected for concealed
damage by uncrating the unit immediately. If any damage is found, it should be reported to
the carrier at once, and a claim should be filed with the carrier. The equipment has been
inspected and tested in the Nor-Lake manufacturing facility and has been crated in
accordance with transportation rules and guidelines. The manufacturer is not responsible for
freight loss or damage.
INSTALLATION
CASTERS
After the packaging and shipping base have been removed, locate the casters found inside
the cabinet. Attach the casters to the bottom of the cabinet using the bolts found installed in
the base (four bolts /caster). The casters with the brakes should be installed in the front of
the cabinet. Do not operate the unit without casters or legs installed.
CLEANING
The exterior of the cabinet and doors may have been protected with a plastic covering. Peel
this protective covering before installation. After removing the covering, clean the interior and
exterior surfaces of the unit with soap and water and rinse with clean water. Dry with a soft
cloth. Do not use chlorinated cleaners on the cabinet as they can cause corrosion. Do not
use abrasive cleaners or pads as they can scratch the surfaces.
DOOR ALIGNMENT
If the doors have come out of alignment during transit, they can be adjusted.
This is
accomplished by losing the screws on the door hinges, adjust the door so it is aligned
properly and tighten the hinge screws. Note: the door on model ZF071 is field-reversible.
Should you require instructions for reversing the door, please contact Nor-Lake service and
request the instructions (PN 150566).
SHELVES
The shelves and shelf clips are packaged inside the cabinet. Install the shelf clips on the
pilasters inside the unit and set the shelves on the shelf clips. The shelves are adjustable in
½" increments.
LOCATION
The refrigeration system located in the back of the unit requires space for proper operation.
In order to assure proper airflow, allow a minimum of four (4) inches on ZR cabinets and six
(6) inches on ZF cabinets of clear space on the sides and back of the cabinet.
1
02/15 150139 Rev. E
Publicité
Table des Matières
Sommaire des Matières pour Norlake ZR152 Serie
- Page 1 ICE CREAM TOPPING CABINET MODELS ZR152, ZF152 and ZF071 Installation, Operation and Maintenance Instructions INSPECTION When the equipment is received, all items should be checked against the bill of lading to insure all crates and cartons have been received. All units should be inspected for concealed damage by uncrating the unit immediately.
- Page 2 Do not locate the unit next to heat generating equipment or in direct sunlight. Improper installation will void the warranty. Confirm that the proposed electrical outlet has the correct voltage, frequency and current carrying capacity for the requirements of the unit. Refer to the serial plate located on the inside left wall of the cabinet for electrical information.
- Page 3 CONDENSER COIL Prior to cleaning the condenser coil, disconnect the unit from power. Periodic cleaning of the condenser coil will aid the heat transfer of the system and improve its efficiency. Cleaning is recommended a minimum of every six months. The condenser coil is located behind the back panel.
- Page 4 REFRIGERATION SYSTEMS - ALL MODELS MALFUNCTION POSSIBLE CAUSE SOLUTION Compressor will not start - no hum 1. Unplugged or power off 1. Plug in service cord or turn on power 2. Fuse blown or removed 2. Replace fuse 3. Overload tripped 3.
-
Page 5: Nettoyage
ARMOIRES À GARNITURE DE CRÈME GLACÉE MODÈLES ZR152, ZF152 et ZF071 Instructions D'Installation, de Fonctionnement et D'Entretien INSPECTION Dès réception de l’équipement, il est nécessaire de vérifier soigneusement tous les articles selon la lettre de transport afin de vérifier la réception de tous les paquets et cartons. Tous les appareils doivent être inspectés pour déceler tout dommage dissimulé... -
Page 6: Emplacement
EMPLACEMENT Le système de refroidissement situé à l'arrière de l'appareil nécessite un espace adéquat afin de pouvoir fonctionner correctement. Pour assurer le flux d'air correct, permettre au moins quatre (4) les pouces sur les cabinets de ZR et six (6) les pouces sur les cabinets de ZF d'espace clair sur les côtés et le dos du cabinet. -
Page 7: Serpentin Du Condenseur
NETTOYAGE Dès la première installation, les surfaces intérieures de l’armoire et le rail doivent être essuyés périodiquement avec une solution d’eau chaude et de bicarbonate de sodium. Cette solution permet de supprimer toutes les odeurs provenant d’éventuels renversements. L'extérieur de l'armoire doit également être nettoyé... - Page 8 GUIDE D’ENTRETIEN ET D’ANALYSE SYSTÈMES FRIGORIFIQUES – TOUS MODÈLES MALFUNCTION CAUSE POSSIBLE DE LA SOLUTION DÉFECTUOSITÉ Le compresseur ne démarre pas — aucun bruit Débrancher ou couper l'alimentation Brancher le cordon d’alimentation ou Fusible grillé ou enlevé mettre l’appareil sous tension Surcharge déclenchée Remplacer le fusible Contrôle bloqué...