Chamberlain LiftMaster Professional WGO 200 Manuel D'instructions page 16

4.1 HELP... TROUBLE SHOOTING
PROBLEM:
1.0 The gate does not open when a pulse is
given.
1.1 A motor opens and the other closes.
1.2 Motors stop immediately.
1.3 The gate does not close after opening.
1.4 The Flashing lamp does not work.
1.5 The keyswitch does not work.
1.6 Motors work slowly after some years of
operation.
2.0 Fuse 0.8 amp. burned.
2.1 Fuse 4 amp. burned.
2.2 Fuse 10 amp. burned.
3.0 Red LED off.
4.2 SPARE PARTS
Art. no. Description
041DR196-2 Stainless steel tube with clevis
041R296-2 Screw provided with ball bearing, gear and
unlocking system
041DR396 Unlock pivot
041DR496 Reduction gear casing made of nylon-glass
041DR896 Accessory kit for the L+R plates assembly and screws
041DR996-2 Trapezoidal anodized aluminum
041DR1196 Fixation pivots and rings
041DR1496 Unlock plug
041DR1596 Unlock key
041DR2296 6002 zz type drive shaft ball bearings
041DR2696 Motor casing with magnets
041DR2896 Actuator lower protection
041DR3796 Front guide
041DR3896-2 Threaded rod (4 pieces)
041DR3996 Rotor provided with manifold and winding
041DR4096 Motor nylon cap provided with brushes holder
041DR6896 628 zz type drive shaft ball bearing
041DR7096 Motor brush
041DR7196 Plastic casing for electronic equipment with cover
041DR7296 230/12V toroidal transformer
041DR7396 Fairleads
041A5408-CDS RF-Module
041A801337 Universal Receiver
041DCTR35-2 Logic Board
041DRWGO200 Arm
4.3 ACCESSORIES
Art. no.
94330E
94333E
94335E
100034
100041
100263
041AD7500
ANT4X-1LM
709145B-GB - 05.2004
CAUSE:
1. Battery discharged.
2. 230V power supply is missing.
3. The back-up battery is empty..
4. Only one motor is connected.
1. M1/M2 wrong connection.
1. Incorrect power.
2. Force stop has been activated.
1. Photocells jumper and/or photocells
alignment. Fuses.
2. Automatic closure not activated.
3. START contact.
1. Bulb fault.
2. Fuse fault.
1. Connection fault.
1. Brushes fault.
1. Transformer burned.
2. Short circuit in the motors supply.
1. Flashing lamp fault.
2. Photocells fault.
1. Battery fault.
1. AC 230V power supply.
Fig. 17
Description
1-channel transmitter
3-channel transmitter
3-channel mini transmitter
Keyswitch
Keyswitch
Infrared sensor kit
Flashing lamp
Antenna
REMEDY:
1. Replace battery of the remote control or temporarily use the
keyswitch.
2. Check the 230V power supply switch or the fuse of the transformer
amp. 0.8.
3. Switch jumper to a different position.
1. Invert the connection cables to motors, refer to fig. 12.
1. Repeat the automatic force adjustment.
1. If no photocells are installed connect the terminal 1 with terminal 2.
Align photocells. Check fuse 5A.
2. Re-program auto 2.
3. START contact permanently active. Check.
1. Check the 12V max. 10W bulb.
2. Check fuse 5A.
1. Check electronic connections. Refer to Fig. 12.
1. Replace electric brushes.
1. Check the transformer isolation.
2. Check motor cables.
1.Check, if there are short circuits in the supply of:
1. Flashing lamp or 2. Photocells.
1. Check battery status.
1. Check 0.8 Amp. fuse.
2. Check the AC 230V power supply connection.
5. WARRANTY
LiftMaster warrants to the first retail purchaser of this product that the
product shall be free from any defect in materials and/or workmanship
for a period of 24 full months (2 years) from the date of purchase for
the automated swing gate opener WGO200. Upon receipt of the
product, the first retail purchaser is under obligation to check the
product for any visible defects.
Conditions: The warranty is strictly limited to the reparation or
replacement of the parts of this product which are found to be
defective and does not cover the costs or risks of transportation of the
defective parts or product.
This warranty does not cover non-defect damage caused by
unreasonable use (including use not in complete accordance with
LiftMaster's instructions for installation, operation and care; failure to
provide necessary maintenance and adjustment, or any adaptations of
or alterations to the products), labor charges for dismantling or
reinstalling of a repaired or replaced unit or replacement batteries.
A product under warranty which is determined to be defective in
materials and/or workmanship will be repaired or replaced (at
LiftMaster's option) at no cost to the owner for the repair and/or
replacement parts and/or product. Defective parts will be repaired or
replaced with new or factory rebuilt parts at LiftMaster's option.
This warranty does not affect the purchaser's statutory rights under
applicable national legislation in force nor the purchaser's rights
against the retailer arising from their sales/purchase contract. In the
absence of applicable national or EC legislation, this warranty will be
the purchaser's sole and exclusive remedy and neither LiftMaster nor
its affiliates or distributors shall be liable for any incidental or
consequential damages for any express or implied warranty relating to
this product.
No representative or person is authorized to assume for LiftMaster any
other liability in connection with the sale of this product.
5-GB