Installation Instructions; Operating Instructions; Maintenance; Cleaning - UBERHAUS DESIGN WW11991 Mode D'emploi

Step 1 : Wheels Assembly
1.Remove the mantel, insert,4 wheels and hardware pack with precaution from the box.
Turn the unit so it sits on its top. Attach the wheels onto the mantel bottom using the
screws(Fig 3) provided(See Fig 4)
Note : The insert has been mounted into mantel before shipment
Step 2 :Plugging in the heater
Note 1.This heater is for use on 120 Volts.
2.A 15 Amp Circuit is required to operate this appliance. If the breaker trips
when the appliance is running, you may need to move the appliance to
another location or unplug other appliances that are on the same circuit.

OPERATING INSTRUCTIONS

Read all instructions and warnings prior to operating the
appliance. Ensure that all controls are in the OFF"position
before plugging the appliance into an adequate electric
outlet.
Switches operation
Master Power Switch(A)
Supply power to all unit functions(Heat/Flame)
Low heat Setting(B)
Supplies power to heater fan and heater element when
the switch is in the I"position the heater operates on low
High Heating Setting(C)
A B C
Supplies power to heater fan and the heater element
when the switch is in the II"position the heater operates
on high. The button B" must also in the I" position for
the high heat setting to operate
Fig A
Note
Light bulbs may become loose during shipping.If the flame effect is
dim or does not operate properly at first, ensure that the light bulbs
are properly secured in the sockets (bulbs should be finger tight, do
not over tighten),See Replacing Light Bulb Section of the manual for
instructions.
When you first turn the heater on, it may emit a slight but harmless
odor resulting from certain oils or greases being heated as the appliance
is used for the first time. This odor is perfectly safe and will stop
shortly. It will not reoccur after the first operation of this appliance.
This appliance comes equipped with an overheat protection safety
device. Should the appliance begin to overheat for any reason, it will
automatically turn all heater functions of the appliance off. The
appliance will have to be reset prior to continuing use. To reset the
overheat protection safety device, turn all controls off and unplug
the appliance, wait 10 minutes, plug the appliance back in and
turn on. If the appliance continuously overheats, please call our
customer service department toll free at 1-866-206-0888.

INSTALLATION INSTRUCTIONS

"
"
"
" "
A B C

MAINTENANCE

WARNING:Before attempting to perform any maintenance on this
appliance,turn all controls to the OFF" position and unplug.Allow
the appliance to be OFF" for at least 10 minutes before performing "
any maintenance in order to allow all components to cool properly
REPLACING LIGHT BULBS:
1.Ensure that all controls are off, the appliance is unplugged
and bulbs are cool to the touch.
2.Wear latex gloves to ensure that grease/oil from your hands does
not transfer to the bulbs.
3.Remove back panel to access light bulbs(see Fig B)
4.Remove the burnt out light bulb and replace with a new bulb.
Hand-tighten the bulbs only,do not over tighten.
5.Replace back panel and screws(see Fig B)
Fig B
Access Panel
Screws

CLEANING:

1.To remove dust from glass window, use a clean dry cloth.
2.To remove fingerprints or other marks from glass window, use a
clean damp cloth. Do not spray glass cleaner or other liquids
directly onto the window.
3.Clean metal surfaces with a clean damp cloth making sure not
to push dust or debris into any air intake or exhaust vents.
4.Do not use abrasive cleaners or spray liquids on any part of
the appliance.
5.Periodic cleaning/vacuuming of the fan/heater unit is
strongly recommended to ensure that no dirt or foreign
objects build up.
"
WARNING:
Do not exceed the
recommended bulb wattage. Use
only 120V, 40W,E12 Chandelier
Light Bulb, Candelabra Base. The
lamp holder is model E12.
Hint:It is a good idea to
replace all light bulbs at one
time if they are close to the end
Light
of their life.Group replacement
will reduce the number of times you
Bulbs
need to open the unit to replace
light bulbs.
3