Publicité
Les langues disponibles
Les langues disponibles
3. Maintenance & Winter Storage
A) Maintenance
1) Disconnect ALL power from the fountain and lights before attempting any maintenance.
2) Periodically clean light set lens with a non-abrasive brush and cleaner. We recommend Airmax
B) Winter Removal & Storage
1) Remove the fountain and lights from the pond before ice begins to form.
2) This is the perfect time to clean or power wash any debris on the unit before storing.
3) It is recommended to disconnect lights from fountain and store in an area above freezing temperatures.
C) Spring Installation Inspection
1) Before re-installing the fountain and lights in the spring, check the condition of the power cord and quick disconnect. Replace any o-rings that
may be worn.
4. Troubleshooting
IF ALL LIGHTS OFF
ISSUE
GFCI Tripped
Power Cord Cut
Water in fixtures
Voltage not high enough for starting
Timer not running
Timer trippers are not set correctly
Photocell defective
IF ONE OR MORE (NOT ALL) LIGHTS OFF
ISSUE
Water in fixtures
LED bulb driver failed
LED Bulb failed
IF LIGHTS DIM
ISSUE
Voltage not high enough for starting
Lens might be dirty
5. Replacement Parts
LED Light Replacement Parts
1. #651307 – Mounting Clamp
2. #651325 – Tension Screw, ¼ - 20 x 1 ¼"
3. #651722 – Bolt, ¼ - 20 x 1 ¼"
4. #651723 – Washer, ¼"
5. #651308 – Band Clamp
6. Power Cord Options
#652646 – 100 feet, 16/3
#652647 – 150 feet, 16/3
#652648 – 200 feet, 16/3
#652649 – 250 feet, 16/3
#652667 – 300 feet, 16/3
#652668 – 350 feet, 16/3
#652669 – 400 feet, 16/3
7. #651060 – Strain Relief (16 gauge)
8. #651357 – Power Cord End Cap, Female
9. #651163 – Female End Cap, O-Ring
4
CORRECTION
Reset GFCI
Repair or replace power cord
Contact Airmax
®
or local dealer for repair/replacement
Make sure voltage at receptacle is 120V+-5%
Verify timer is keeping time, replace timer if not
Set on / off trippers correctly
Replace photocell
CORRECTION
Contact Airmax
or local dealer for repair/replacement
®
CORRECTION
Make sure voltage at receptacle is 120V+-5%
Clean with a non-abrasive brush or cleaner
®
Fountain & Aeration Cleaner (#530298)
IF ONE OR MORE (NOT ALL) LIGHTS DIM
ISSUE
Water in fixtures
Photocell defective
LED bulb driver failed
IF LIGHTS FLICKER
ISSUE
Water in fixtures
Voltage not high enough for starting
LED bulb driver failed
IF LIGHTS TURN ON AND OFF INTERMITTENTLY
ISSUE
Water in fixtures
Photocell defective
LED bulb driver failed
NOTE:
Pre-Programmed light modes can cause lights to dim, flicker, and fade in and out. When trouble
shooting, please ensure you are in the basic ON mode by turning the unit off with the "MASTER OFF"
button, then press and hold "MASTER ON" for several seconds to turn all lights to white mode. (Fig. 6)
ENGLISH
CORRECTION
Contact Airmax
®
or local dealer for repair/replacement
Replace photocell
Contact Airmax
or local dealer for repair/replacement
®
CORRECTION
Contact Airmax
®
or local dealer for repair/replacement
Make sure voltage at receptacle is 120V+-5%
Contact Airmax
or local dealer for repair/replacement
®
CORRECTION
Contact Airmax
or local dealer for repair/replacement
®
Replace photocell
Contact Airmax
®
or local dealer for repair/replacement
Publicité
