Publicité
Les langues disponibles
Les langues disponibles
LED recessed lighting,
10-piece set, colour-changing
Item no. 57 76 65
1.
Intended use
The 10 LED lights are intended for mounting on fl oors, walls or ceilings (e.g. wooden ceiling panelling)
and provide illumination. The remote control unit and control unit can control the lights to display different
colours via the integrated RGB-LED. The remote control is powered by a CR2025 button cell battery and the
control unit is powered by the included 12 V/DC power adaptor. The remote control, control unit and the
power adaptor should only be used in dry indoor environments. However, the 10 LED lights may be used in an
outdoor area. Please, take notice that the LED lights must not be used under water!
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fi re, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
Delivery content
•
Control unit
•
Remote control
•
Button cell battery type CR2025
•
10 Recessed LED lights
•
15 m extension cable
•
Protective cap
•
Power adaptor
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
•
Do not place any sources of open fi re, such as burning candles, on or next to the product.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
fl ammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
Check the product for damage before use! Any maintenance or repair work should only be performed by
authorised personnel.
If you detect any damage, do NOT connect the device to the mains voltage! This presents a danger to life!
Safe operation must be presumed to be no longer possible:
-
if the device is visibly damaged
-
if the device no longer works
-
the device was stored under unfavourable conditions for a long period of time or
-
it was exposed to extraordinary stress caused by transport
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
•
Do not drill any holes or insert any screws into the housing to attach or mount the product. This can damage
the product and interfere with safety.
•
Also observe the safety and operating instructions of any other devices which are connected to the
product.
•
Never pour liquids over electrical appliances and never leave objects fi lled with liquids (e.g. vases) on it or
in the vicinity. There is a high risk of fi re or life-threatening electric shock.
•
In schools, training facilities, hobby or self-service workshops, handling of electrical devices must be
monitored by trained personnel.
•
When operating on commercial premises, the relevant accident prevention regulations of workers'
compensation boards for electrical equipment must be observed.
•
Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of
injury.
•
When working with power supplies or chargers, do not wear any metallic or conductive chains, bracelets,
rings etc. Never connect the power supply or charger with humans or animals.
•
Use only a proper mains socket (100 - 240 V/AC, 50/60 Hz) connected to the public power supply.
•
Do not pull the mains adapter out of the wall outlet by its cable!
•
The plug must be pulled out of the socket under the following conditions:
-
before cleaning the product
-
during a thunder storm
-
if the product is not being used over a long period.
•
When setting up the product, make sure that the cable is not pinched, kinked or damaged by sharp edges.
•
Make sure there are no devices with strong electric or magnetic fi elds such as transformers, motors,
cordless telephones and radio-controlled devices in the vicinity of the product as these can infl uence the
product.
•
Never look directly into the shining lights as this can (just as with other lights) cause eye damage!
•
Ensure that the insulation of the entire product is neither damaged nor destroyed. Don't open the housing
of the adapter or control unit! There are no serviceable parts inside the housing.
•
Due to the use of LED technology, there is no need to change lamps or bulbs. This is not possible.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifi cations and repairs are to be performed exclusively by an expert or at a qualifi ed
shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
Operating elements
1
2
3
Version 05/11
14
13
12
11
10
9
1.
Connector to the LED lights
2.
Power connector to the power adaptor
3.
IR receiver
4.
LED light
5.
Protective cap
6.
Connector to the control unit
7.
Power adaptor
8.
Power connector to the control unit
5.
Mounting preparations, choosing the mounting place
1
5
1.
LED lights
2.
Cable implementation for connection cables
3.
Power adaptor
4.
Control unit
5.
16 mm holes
The lights can be mounted e.g. on the terrace (wooden boards) or also in wall boards or on ceilings (wooden
ceilings). Because of the design of the lights many other installation places are imaginable, that with
conventional lightings are not possible.
The maximum distance between the lights is set by the premounted connection cable. The 10 lights are simply
connected in series, the output of one light leads to the next. This simplifi es the mounting, in particular.
The fi tting of the lights takes place with e.g. a few drops of hot-glue or construction silicone.
6.
Installation
Ensure again that no cables or wires are damaged when drilling. Danger to life!
•
You can also use less than 10 lights, you don't need to use all 10 lights.
•
The distance between two lights must not exceed 95 cm. If there are obstacles, the distance
may be shorter. Ensure that all the lights and the control unit can be connected via the cable
at their selected locations before drilling.
•
The cable should not be squeezed when closing a door or window.
1.
When you specifi ed the installation place for the 10 lights, drill a corresponding hole for every light (approx.
diameter 16 mm).
2.
Lead the connection cable through the hole.
3.
The fi tting of the lights in the holes can be done with, for example, a few drops of hot-glue or another
suitable glue for outdoor areas, or contruction silicone.
4.
Crosslink the lights. Connect the connection cable of the fi rst light with the control unit, the open connection
of the last lights should be sealed with the included end cap, so no moisture can come in.
4
5
6
8
7
9.
Button "W"
10.
Button
11.
Button
12.
Buttons « Fast/Med/Slow »
13.
Buttons « R/G/B/autres couleurs »
14.
Button
3
2
4
5.
The long cable serves for connection of the fi rst light on to the control unit. Lead the cable through a wall
opening in the inner room. Close the opening with, for example, mortar resp. a suitable glue or construction
silicone.
6.
The control unit can, for example, be fi xed on a wall with screws through two holes at the rear side.
7.
Finally, connect the circular connector of the AC adapter with the low voltage socket of the control unit. Plug
the AC adapter into a mains socket (100 – 240 V/AC, 50/60 Hz).The control unit can, for example, be fi xed
on a wall with screws through two holes at the rear side.
7.
Operation
You can control the lighting effect of the lights with the
remote control.
1.
Hold your remote control and aim it at the IR receiver
of the control unit.
2.
Press the button to change the lighting effect.
Button "W"
White light will be emitted.
The brightness of the white light will be increased / decreased
Button
in nine different levels. The brightness of the other colour lights
cannot be adjusted.
Button
Buttons "Fast/Med/Slow"
The automatic colour change is activated. The speed of the
colour change can be set to fast, medium or slow.
Buttons "R/G/B/other colours"
Press on the desired colour and light in that colour will be
emitted.
Turn on/off the lights.
Button
8.
Maintenance and care
•
Apart from occasionally cleaning, the product is maintenance-free, do not dismantle to clean. A change of
lamp is not necessary due to the high product life of the light diodes.
•
Before cleaning, disconnect the device from the power source.
•
Clean the product with a soft, clean and dry cloth. Do not use strong cleaning agents or chemical solutions
as the surface of the housing could be damaged (e.g. discolouration).
9.
Disposal
In order to preserve, protect and improve the quality of environment, protect human health and
utilise natural resources prudently and rationally, the user should return unserviceable product to
relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately and not as
municipal waste.
10.
Technical data
General
Operating voltage:
12 V/DC
Operating voltage (remote control): 3 V button cell battery, type CR2025
Power output per LED:
75 mW
IR Reception range:
6 m
Protection class (LED):
IP 66
Installation ø:
16 mm
Installation depth:
45 mm
LED Dimensions (ø x L):
19 x 40 mm
LED cable length:
1 m each
Power Adaptor
Input voltage:
100 - 240 V/AC, 50/60 Hz
Output voltage:
12 V/DC
Output current:
max. 500 mA
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfi lming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions refl ect the current technical specifi cations at time of print.
We reserve the right to change the technical or physical specifi cations.
© 2010 by Conrad Electronic SE.
IR receiver
V2_0511_02-HL
Publicité
