Installation Instructions; Power Unit - Ain King SEV24S Mode D'emploi

Unité de puissance
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

INSTALLATION INSTRUCTIONS

CAUTION:
SERVICE PANEL BEFORE STARTING INSTALLATION.
SECTION 1
Preparing the Insert
1.
Unpack hood from the carton and confirm that all pieces are present. In addition to the
range hood you should have:
1 - Duct collar
1 - Wire compartment
SEV24 models: 2 - Aluminum Grease Filters (shipped installed)
SEV28 and SEV30 models: 3 - Aluminum Grease Filters (shipped installed)
2 - 50 watt Halogen lamps
1 - Instruction/Safety Sheet
NOTE: Some hoods may be shipped with a protective plastic adhered to the underside of the
unit. It is recommended to leave this in place during installation to protect it from scratching.
Remove when the installation is complete.
SECTION 2
Preparing the Area
CAUTION:
SERVICE PANEL BEFORE STARTING INSTALLATION.
CAUTION:
WHEN CUTTING OR DRILLING INTO WALL DO NOT
DAMAGE ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.
1.
Most building codes require noncombustible material above the cooking surface. If
you you have wood or some other combustible material on the bottom of your cabinets
it is recommended that you use the optional hood liner (See Section 3) If you have
noncombustible material cut an appropriate size hole into the cabinet or canopy the
power unit will be mounted into (Figure 1):
SEV24 models: 18" wide by 10" deep.
SEV28 models: 26-7/8"" wide by 10" deep.
SEV30 models: 30" wide by 10" deep
18" / 26-7/8" / 30"
Figure 1
NOTE: The hood must be mounted a minimum of 24" and a maximum of 36" from the
cooking surface.
SECTION 3
Optional Hood Liner
CAUTION:
MAKE SURE THE SURFACE YOU ARE MOUNTING THE
INSERT AND LINER TO IS CAPABLE OF SUPPORTING THE WEIGHT OF THE UNIT.
OTHERWISE YOU WILL NEED TO REINFORCE THE AREA.
1.
Secure the liner to the cabinet frame or custom canopy using three screws on each end
of the liner and 3 screws on each side of the top of the liner (Figure 2).
Figure 2
6728012 Rev. O 4-17
MAKE SURE POWER IS SWITCHED OFF AT
MAKE SURE POWER IS SWITCHED OFF AT
10"
SECTION 4
Installing the Insert
2.
Insert the power unit into the hole and secure to liner using the screws provided with the
Liner (Figure 3).
Figure 3
NOTE: If an optional Air King Liner is not being used; use appropriate hardware to install the
unit in place, making sure to comply with all Local and National Building Codes.
CAUTION:
POWER UNIT TO IS CAPABLE OF SUPPORTING THE WEIGHT OF THE UNIT.
OTHERWISE YOU WILL NEED TO REINFORCE THE AREA.
SECTION 5
Ducting
CAUTION:
BUILDING CODES.
1.
Install the included duct collar to the hood with two of the provided #6 blunt tip screws
(Figure 4).
Duct Collar
Figure 4
2
When there is access to the top of the unit, connect the ducting to the duct collar and
secure in place using tape to seal all joints (Figure 4).
3.
When there is no access to the top of the hood, carefully pull down the metal duct through
the custom hood base hole. Slide this duct over the duct collar. Make sure the adapter/
damper assembly enters the ducting. Seal the connection with duct tape.
NOTE: To achieve proper air flow, 6" round ducting is required. The duct connector is 5.8" in
diameter (for 6" round ducting) and the center is located 3.1875" inches from the back wall.
CAUTION:
WALL OR ROOF CAP.
SECTION 6
Wiring
ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL
WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.
3
Examine the wire compartment cover and select the most convenient wire entrance
and remove the knock out. Feed the supply wire through the opening and install an
appropriate strain relief. Connect the white wire from the power unit to the white wire
from the supply. Connect the black wire from the power unit to the black wire of the
supply. Connect the ground wire from the home (green or bare) to the ground wire of the
power unit (green or green/yellow). Use approved methods for all connections (Figure 5).
www.airkinglimited.com
MAKE SURE THE SURFACE YOU ARE MOUNTING THE
ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL
WARNING:
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A
CAUTION:
ALL ELECTRICAL CONNECTIONS MUST BE MADE
IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL
Ducting

Power Unit

2 of 12

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Sev28sSev30sSev24abSev28abSev30ab

Table des Matières