Optional Accessory; Specifications - Troy-Bilt TB2040 XP Manuel De L'utilisateur

OPTIONAL ACCESSORY

ELECTRIC STARTER AND POWER START BIT™ FEATURES
This unit is designed to be started with an optional
electric starter or Power Start Bit™ that are sold
separately. If choosing to start the unit using one of
these features or have questions please contact your
local retailer or call 1-800-828-5500 U.S, (1-800-668-
1238 Canada), for more information and purchasing.
You may also go to www.troybilt.com or
www.troybilt.ca.
TROUBLESHOOTING
ENGINE WILL NOT START
CAUSE
Empty fuel tank
Primer bulb wasn't pressed enough
Engine is flooded
The fuel is old (over 30 days) and/or improperly mixed
Fouled spark plug
ENGINE WILL NOT IDLE
CAUSE
Air filter is plugged
The fuel is old (over 30 days) and/or improperly mixed
Improper carburetor adjustment
ENGINE WILL NOT ACCELERATE
CAUSE
The fuel is old (over 30 days) and/or improperly mixed
Cutting head bound with grass
Dirty air filter
ENGINE LACKS POWER OR STALLS
CAUSE
The fuel is old (over 30 days) and/or improperly mixed
Fouled spark plug
ENGINE STOPS WHILE IN USE
CAUSE
Engine overspeed protection engaged
CUTTING HEAD WILL NOT ADVANCE LINE
CAUSE
Cutting head bound with grass
Cutting head out of line
Inner reel bound up
Cutting head dirty
Line welded
Line twisted when refilled
Not enough line is exposed
CUTTING LINE ADVANCES UNCONTROLLABLY
CAUSE
Oil, cleaner or lubricant in cutting head
IF FURTHER ASSISTANCE IS REQUIRED, CONTACT AN AUTHORIZED SERVICE DEALER.
Electric Start Feature
Fig. 19
ACTION
Fill fuel tank with properly mixed fuel
Press primer bulb fully and slowly 10 times
With blue choke lever in position 3, squeeze the trigger
and pull the starter rope
Drain fuel tank and add fresh, properly mixed fuel
Replace or clean the spark plug
ACTION
Replace or clean the air filter
Drain fuel tank and add fresh fuel mixture
Adjust according to the Carburetor Adjustments section
ACTION
Drain fuel tank and add fresh fuel mixture
Stop the engine and clean the cutting head
Clean or replace the air filter
ACTION
Drain fuel tank and add fresh fuel mixture
Replace or clean the spark plug
ACTION
Allow the engine to cool down for 10 minutes before
restarting.
ACTION
Stop the engine and clean cutting head
Refill with new line
Rewind the inner reel
Clean inner reel and outer spool
Disassemble, remove the welded section and rewind
Disassemble and rewind the line
Push the bump knob and pull out line until 4 inches (102 mm)
of line is outside of the cutting head
ACTION
Clean and thoroughly dry the cutting head
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10 in. (2.8 cm)
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 cc
Operating RPM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,800+ rpm
Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,800 - 3,400 rpm
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 in. (0.635 mm)
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture
Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40:1
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 fl.oz. (397 ml)
Approximate Unit Weight (No fuel, with cutting attachment, shield and D-handle) . . 11 - 13 lbs. (4.9 - 5.9 kg)
Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Proulx
Line Spool Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 in. (114.3 mm)
Trimming Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.095 in. (2.41 mm)
Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 in. (45.72 cm)
*All specifications are based on the latest product information available at the time of printing. We
reserve the right to make changes at any time without notice.

SPECIFICATIONS

5