Maintenance Instructions; Moving And Storage Instructions - Schumacher Electric SJ1331 Manuel D'utilisation

4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the unit to run
appliances that draw more than 20A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the unit immediately after
unplugging the 12V DC device.
Estimated run-times
APPLIANCE TYPE
Cell phone, fluorescent light
Radio, fan, depth finder
Camcorder
Electrical tool
Electric cooler
Car vacuum, air compressor
NOTE: Actual time may vary. Times are based
on the internal battery being fully charged.
5.5 USING THE AIR COMPRESSOR
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
NOTE: Wrap cleats are provided for
convenient storage of the air compressor

6. MAINTENANCE INSTRUCTIONS

6.1 After use and before performing
maintenance, unplug and disconnect
the jump starter.
6.2 Use a dry cloth to wipe all battery corrosion
and other dirt or oil from the battery clips,
cords and the jump starter case.

7. MOVING AND STORAGE INSTRUCTIONS

7.1 Store inside, in a cool, dry place.
7.2 Do not store the clips on the handle,
clipped together, on or around metal, or
clipped to cables. The clips on the jump
starter are live when the switch is in the
ON position and will produce arcing or
sparking if they come in contact with each
other. To prevent accidental arcing, always
place the switch in the OFF position and
keep the clips on the storage holders when
not using it to jump start a vehicle.
7.3 If the jump starter is moved around the
shop or transported to another location,
take care to avoid/prevent damage to the
cords, clips and jump starter. Failure to
do so could result in personal injury or
property damage.
IMPORTANT: Do not use and/or store the
jump starter in or on any area or surface
EST APPROX.
WATTAGE USAGE
4 watts 34 hrs
9 watts 14 hrs
15 watts 7 hrs
24 watts 5 hrs
48 watts 2 hours
80 watts 1.8 hrs
hose. Wrap the hose around these cleats
when the hose is not in use.
1. Ensure the battery clips are securely
on the storage holders.
2. Remove the air compressor hose from
the storage cleats.
3. Connect the adapter to the valve
stem by threading it onto the end. If
necessary, use one of the additional
adaptors.
4. Press the air compressor power switch
to turn ON and inflate to the desired
pressure or fullness (refer to the gauge
next to the switch).
5. When the desired pressure is reached,
press the air compressor power switch
to turn OFF and remove the connector
from the valve stem.
6. Allow unit to cool.
7. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air
compressor gauge to ensure the proper
pressure has been reached. Do not overinflate.
6.3 Ensure that all of the jump starter
components are in place and in good
working condition.
6.4 All servicing should be performed by
qualified service personnel.
where damage could occur if the internal
battery should unexpectedly leak acid.
7.4 IMPORTANT:
• CHARGE IMMEDIATELY AFTER
PURCHASE
• KEEP FULLY CHARGED
Charge the jump starter's internal battery
immediately after purchase, after every
use and every 30 days.
All batteries are affected by temperature. The
ideal storage temperature is at 70°F. The
internal battery will gradually self-discharge
(lose power) over time, especially in warm
environments. Leaving the battery in a
discharged state may result in permanent
battery damage. To ensure satisfactory
performance and avoid permanent damage,
charge the internal battery every month.
• 7 •
6-24 minutes
1-3 minutes
30 seconds