Ferm GRM1022 Traduction De La Notice Originale page 5

• The machine shall be disconnected from its
power source by removing the plug from the
socket-outlet during cleaning or maintenance
and when replacing the machine to another
function.
• Observe a distance of at least 30cm when
using the jet to clean painted surfaces to avoid
damaging paintwork.
• Do not use the machine if a supply cord or
important parts of the machine are damaged,
e.g. safety devices, high pressure hoses,
trigger gun.
• If an extension cord is used, the plug and
socket must be of watertight construction.
• Inadequate extension cords can be dangerous.
If an extension cord is used, it shall be suitable
for outdoor use, and the connection has to be
kept dry and off the ground. It is recommended
that this is accomplished by means of a cord
reel which keeps the socket at least 60mm
above the ground.
• In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this
appliance must not be supplied through an
external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
• To ensure the machine safety, please only
use original spare parts (including nozzle)
from the manufacturer or approved by the
manufacturer. Do not use the machine before
you changed them if they are damaged.
• Be care of the danger of the kickback force on
the spray assembly when opening the trigger
gun and grasp the gun with hands firmly.
• To reduce the risk of injury, close supervision
is necessary when a machine is used near
children. High-pressure cleaner shall not be
used by children or untrained person.
• Know how to stop the machine and bleed
pressures quickly. Be thoroughly familiar with
the controls.
• Stay alert and watch what you are doing.
• Do not operate the machine when fatigued or
under the influence of alcohol or drugs.
• Keep operating area clear of all persons.
• Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
• Follow the maintenance instructions specified
in the manual.
• This machine must be grounded. If it has
malfunction or breakdown, grounding provides
a path of least resistance for electric current to
reduce the risk of electric shock. The plug must
be plugged into an appropriate outlet that is
properly installed and grounded in accordance
with all local codes and ordinances. The rating
voltage (V/Hz) of the machine has to be in
compliance with the local power supplying
voltage.
• Check with a qualified electrician or service
personnel if you are in doubt as to whether the
outlet is properly grounded. Do not modify the
plug provided with the machine. If it will not
fit the outlet, have a proper outlet installed by
a qualified electrician. Do not use any type of
adapter with this machine.
• Use only 3-wire extension cords that have
3-prong grounding-type plugs and 3-pole
cord connectors that accept the plug from the
machine. Use only extension cords that are
intended for outdoor use and the socket must
be of watertight construction. These extension
cords are identified by a marking "Acceptable for
use with outdoor machines; store indoors while
not in use." Use only extension cords having
an electrical rating not less than the rating of
the machine. Do not use damaged extension
cords. Examine extension cord before using and
replace if damaged. Inadequate extension cords
can be dangerous. Do not abuse extension cord
and do not yank on any cord to disconnect.
Keep cord away from heat and sharp edges.
Always disconnect the extension cord from the
receptacle before disconnecting the machine
from the extension cord.
• To reduce the risk of electrocution, don't start
and run the machine in the rain or storm. Keep
all connections dry and off the ground. Do
not touch plug with wet hands. It is strictly
prohibited to let water leak into the machine.
• When the machine is running, please maintain a
constant water supply. Without water circulation
will damage the sealing rings of the machine.
• It is necessary to turn on the spray lance within
one or two minutes after the machine has been
started. Otherwise, the temperature of the
circulating water within the machine will soon
rise to a critical point, which will cause damage
to the sealing rings inside the machine.
• Don't start and run the machine in a place
excessively cold so as to prevent the machine
5