Publicité
Les langues disponibles
Les langues disponibles
DMP-30
Order Number 17.4500
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
Audio Player Module
These instructions are intended for users
without any specific technical knowledge.
Please read the instructions carefully prior to
operation and keep them for later reference.
1 Applications
The audio player module DMP-30 is designed for
installation into an existing unit, but it can also
be used as a stand-alone unit. For operation, it
re quires a 12 V DC voltage.
The audio player is able to replay audio files
in the formats MP3 and WMA from, for example,
– USB flash drives (64 GB max.)
– USB hard disks
(with separate power supply, if required)
– memory cards (64 GB max.)
– mobile devices
with "Android" operating system
Note: Due to the large number of storage device manu-
facturers and device drivers, it cannot be guaranteed that
all storage media are compatible with the DMP-30.
2 Important Notes
This module corresponds to all relevant directives
of the EU and is therefore marked with
•
The module is suitable for indoor use only. Pro-
tect it against dripping water and splash water,
high air humidity and heat (admissible ambient
temperature range: 0 – 40 °C).
•
For cleaning only use a dry, soft cloth; never use
water or chemicals.
•
No guarantee claims for the module and no
liability for any resulting personal damage or
material damage will be accepted if the mod-
ule is used for other purposes than originally
intended, if it is not correctly connected or op-
erated, or if it is not repaired in an expert way.
If the module is to be put out of oper-
ation definitively, take it to a local recy-
cling plant for a disposal which is not
harmful to the environment.
3 Installation and Connection
1) To install the module into a unit, a cutout of
156 mm × 50 mm mm is required. The instal-
lation depth is 90 mm, without taking into
account the connection jacks and plugs. Push
the module into the cutout and fasten it via its
front panel using four screws.
2) Connect the RCA jacks OUTPUT on the rear to
the line signal input of an audio unit (amplifier,
active speaker system, mixer etc.).
3) For power supply, feed 12 V (⎓) to the low-volt-
age jack. The current consumption is 120 mA*.
For connection, a low-voltage plug 5.5 / 2.1 mm
(outside / inside diameter) is required. Always
observe the correct polarity (centre contact =
positive pole). Use, for example, the power
supply unit PSS-1205DC from MONACOR.
* If a hard disk without separate power supply unit is
connected, its current consumption must be added to
this value.
ELECTRONICS FOR SPECIALISTS
4 Remote Control
1) To insert the batteries (2 × 1.5 V, size AAA), re-
move the battery compartment cover on the
rear of the remote control. Insert the batter-
ies as indicated in the compartment, and then
close the cover.
If the remote control is not in use for a
longer period of time, always remove the
batteries to prevent damage due to battery
leakage.
2) When you press a button on the remote con-
trol, always point the remote control at the
audio player. Make sure that there are no ob-
stacles between the remote control and the
player.
3) If the operating range of the remote control
decreases, the batteries are discharged and
must be replaced.
Never put discharged batteries in the
household waste; always take them to
a special waste disposal, e. g. collection
container at your re tailer.
5 Operation
Connect, for example, a USB flash drive or a hard
disk (with separate power supply, if required) to
.
the USB port
the slot SD / SDHC / MMC (notched corner to the
right and facing the player). To remove the card,
push the card into the slot until it disengages.
All control options can be found in the table on
the right.
Notes:
1. When the sliding switch PLAY MODE on the rear of the
unit is set to a different position, any change of function
will not take effect until the power supply has been
switched off and on again.
2. When switching over the replay from the memory card
to the USB storage medium (or vice versa), any function
selected (e. g. repeat function, single title replay, intro
function) will be deactivated. The position of the sliding
switch PLAY MODE will define whether or not the replay
starts automatically after switching over.
6 Specifications
Frequency response: . . 20 – 19 000 Hz ± 2 dB
Output level: . . . . . . . . 1.4 V
THD: . . . . . . . . . . . . . . < 0.2 %
S / N ratio: . . . . . . . . . . > 65 dB (A weighted)
Power supply: . . . . . . . 12 V (⎓) ±2 V, 120 mA
Ambient temperature: 0 – 40 °C
Dimensions: . . . . . . . . 174 × 51 × 115 mm
Weight: . . . . . . . . . . . 494 g
Subject to technical modification.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
and / or insert a memory card into
ELECTRONICS
Button
Function
sliding switch on the rear:
AUTO PLAY = The replay will start
automatically after the 12 V power
supply has been switched on.
NORMAL = The audio player will be
PLAY
×
set to pause after the power supply
MODE
has been switched on.
RANDOM /AUTOPLAY = Replay in
random order will start automat-
ically after the power supply has
been switched on.
to switch on;
×
to switch off, keep button pressed
×
POWER
for 3 s until
GoodBye
to switch between USB port
FUNC
×
×
and memory card
II
×
to start the replay and to switch
PLAY
×
between replay and pause
PAUSE
direct title selection, examples:
title 8
= buttons 8 and II
1...9, 0
×
×
title 30 = buttons 3, 0 and II
title 125 = buttons 1, 2, 5 and II
previous / next title:
press button briefly
I SKIP I
×
×
fast forward / reverse:
keep button pressed
(sound muted in the process)
to go to the first title of the previ-
FOLDER ×
×
ous / next folder
VOL+
to increase / decrease the volume:
×
VOL−
press button briefly (repeatedly)
MUTE
×
to mute and unmute the sound
to activate and deactivate the
RANDOM
×
×
replay in random order
to select the repeat function:
REPEAT ALL
REPEAT TRACK
REPEAT
×
×
REPEAT FOLDER
PLAY ALL
= function deactivated
to activate and deactivate the intro
INTRO
×
function (The first 10 sec onds of
each title are replayed.)
single title replay: At the end of a
title, the player is set to pause. To
PLAY 1
×
×
start the next title, press the button
II / PLAY PAUSE.
repeat of title section
(continuous loop)
Press the button at the beginning
A-B
×
and at t he end of the section.
To exit the loop, press the button
once again.
to switch the indication between
ID3
×
title information and storage device
selected (USB /CARD)
to program an individual title
sequence:
1. Press the button PROG
2. Enter the folder number and
press the button PROG
3. Enter the title number and press
PROG
×
the button PROG
4. Repeat these steps to program
all further titles (20 max.)
5. Press the button
replay
To delete or cancel the sequence,
press the button ■ / STOP.
to stop the replay; the display
×
■
will indicate the storage device
selected, the number of folders
STOP
×
and titles
A-1578.99.03.08.2016
is indicated
= all titles
= one title
= all titles of the
folder
to start the
Publicité
