Parts Of The Product; Indication; Scope Of Delivery; Safety Instructions - Drive DeVilbiss Healthcare 10495-30 Mode D'emploi

Parts of the product

1
2
3
1. Clamping function screw connection
2. Stainless steel pivoting support handle
3. Fall guard

Indication

INDICATION:
Holding and support element made of stainless steel for
the bath and toilet area. The support handle is mounted
to the bathroom wall and facilitates or supports sitting
down and standing up and enables safe and stable sup-
port of body weight.
CONTRAINDICATION:
Unsuitable for use if persons are not able to sit down and
stand up by themselves.

Scope of delivery

1 x Pivoting support handle
1 x Plastic dowel
6 x Stainless steel screws Ø 6 x 60
1 x Instructions for use

Safety instructions

• Take note of the permitted maximum weight of the
user.
• When pivoting upwards, clothing and body parts can
be pinched.
• Protect the product from direct sunlight
• Prior to each use, ensure that the handle is intact and
all parts are properly secured.
• Do not sit on the pivoting support handle!
• Check the screws regularly and tighten, if necessary.
• Ensure that your hands are dry.

Assembly

For safety reasons, assembly must be performed by an
installation specialist. When attaching the product, the
mounting height according to DIN 18024/25 must be ob-
served. Only use mounting material which is approved
for the structure. After assembly, test the secure hold as
well as the pivoting and clamping function! Adjust the
Drive Medical GmbH & Co. KG | As per: 19.06.2020 | Errors and alterations excepted
clamping function using the
screw connection (photo 1),
if necessary. If the clamping
function is inadequate, the-
2
re is a risk that the handle will
pivot downwards unintenti-
6
onally. The standard moun-
ting supplied contains a plas-
tic dowel as well as stainless
steel screws Ø 6 x 60 accor-
ding to DIN 7995. Since these
5
are suitable only for mounting to the wall types concre-
te B 25, natural stone (dense structure), solid brick (M20)
and sand-lime brick (Ks 12), the composition of the wall
must be checked by a specialist for suitability for atta-
ching the article. For other wall types, a company specia-
lizing in fastening technology must be consulted.

Handling

Pivot the support handle up or down as far as it will go,
as needed.
Do not grip in the clamping area between the wall bra-
cket and the pivoting support handle – risk of crushing!

Cleaning

• Clean regularly with a moist cloth!
• Do not use any aggressive cleaning agents!
• Do not use abrasive cleaners!
• Do not use any high-dose chlorine and vinegar-based
cleaners!
• To disinfect, a spray disinfectant can be used such as
Descosept AF or Bacillol AF.
• Check the screws regularly and tighten, if necessary.
• The product should not be exposed to temperatures
above 60°C for long periods of time (for example, use
in a sauna, etc.).
• In the event of defects, contact your specialist dealer
from whom you purchased this product.

Technical data

Product
Article number
HMV (medical aids
register) no.
Overall length
Mounting plate
width
Mounting plate
length
Tube diameter
Total weight
Max. load
Material
Length 85 cm Length 60 cm
10495-20
04.40.05.1224 04.40.05.1224
85 cm
10 cm
27 cm
3.2 cm
3.4 kg
120 kg
Stainless steel Stainless steel
Instructions for use PIVOTING SUPPORT HANDLE
EN
10495-30
60 cm
10 cm
27 cm
3.2 cm
2.9 kg
120 kg
7