Bluetooth - HK Audio PREMIUM PR:O MOVE 8 Manuel

3 Operating MOVE 8 on Battery Power
MOVE 8 can operate for up to 11 hours on two fully charged batteries,
depending on the volume and signal, and 5.5 hours on one battery. The
battery in slot A always has priority over the battery in slot B. This means
that the battery in slot A is always drained or charged fi rst when the device
is connected to mains power with two batteries installed.
MOVE 8 promptly switches to the battery in slot B when the charge of
battery in slot A is depleted. The choice of slot is irrelevant when operating
the device on just one battery.
Charging Batteries
Batteries may be charged in the slot on MOVE 8 or in an optional quick
charger. It takes around fi ve hours to fully charge one completely empty
battery in the MOVE 8 slot and around ten for both, regardless of whether
MOVE 8 is on or off . In other words, you can operate MOVE 8 at full power
using the mains adapter and charge the batteries at the same time. The
optional quick charger charges the battery in around two 2 hours.
Hot Swap Option
You can change batteries on the fl y while MOVE 8 is up and running. If
MOVE 8 switches to battery B because battery A is depleted, you can
remove battery A without severing the signal and insert a third fully
charged battery, optionally available as an accessory, into slot A. If
necessary, you can also change battery B once the device detects battery A.
The Bluetooth link remains up during a hot swap, so the device can run on
batteries for as long as you care to keep swapping them.
Good to know: You can hot-swap batteries even if you only have just the
factory-included rechargeable batteries. If the device indicates the charge
is running low while you are operating it with just one battery, fi rst insert
the second fully charged battery into the free slot, wait until it is detected,
and then remove the drained battery. Then you can charge it at the nearest
power outlet using the external quick charger.
LED Indicators
The two LEDs on the battery slot serve two purposes:
When operating MOVE 8 on battery power: When batteries are inserted
and MOVE 8 is switched on, the LEDs indicate which battery is currently
supplying voltage and is being drained. Just one LED fl ashes as just one
battery provides power at any one time. The other LED for the battery
that is on standby lights up continuously to indicate it is ready to operate.
The LED does not light up if the slot is empty or a battery has not been
detected.
When operating MOVE 8 on mains power: A fl ashing LED indicates which
battery is currently being charged. The fl ashing stops and the LED lights up
continuously when the battery is fully charged.
100 60 30
Green Yellow
The LEDs' color indicates the state of charge. This applies in both cases –
when the device is receiving mains power and the batteries are charging,
and when it is running on battery power.
Green: 100 – 60% • Yellow: 60 – 30% • Red: 30 – 0%
0%
Red

4 Bluetooth

Pairing a Bluetooth-Enabled Device
• Press the Channel 4 Pairing button
• The blue Bluetooth LED fl ashes slowly and MOVE 8 shows up in the
Bluetooth-enabled device's selection list for 60 seconds
• Select "HK Audio MOVE 8" on the Bluetooth device to pair the devices
• After 60 seconds you have to restart the pairing process if the connection
failed
The Channel 4 Bluetooth LED on MOVE 8 lights up blue as soon as the
devices are paired and remains illuminated.
Pairing a Bluetooth Device Automatically
The next time you power up MOVE 8, the system will automatically search
for the most recently paired device for 10 seconds and, once found, connect
to it. This way, you do not have to pair the Bluetooth-enabled device
manually. If the 10 seconds elapse without MOVE 8 discovering the device,
you can relaunch the search by switching MOVE 8 off and on again or pair
the Bluetooth-enabled device manually.
Switching to Another Bluetooth Device
You cannot switch to another Bluetooth device while a Bluetooth device is
still connected or the MOVE 8 is searching for the most recently connected
device. You will have to repeat the steps to pair a Bluetooth-enabled device,
disconnect the currently paired device, and connect the other Bluetooth
device.
Heads up: Every attempt to pair a Bluetooth-enabled device creates a
fresh Bluetooth connection and severs any existing link!
Range
MOVE 8 supports Bluetooth 5. Bluetooth 5-enabled devices' range can
extend up to 40 meters. Devices that do not support Bluetooth 5 typically
run up to 10 meters, but that depends on factors such as the given device's
quality, transmission power and current environment. For example, walls
obstructing the transmission path or a protective cover on the Bluetooth
device impede radio communication.
The sound drops out if the device moves out of range or behind walls that
interfere with the signal. The connection re-establishes automatically if you
bring the Bluetooth device back in range within 60 seconds, in which case
the Bluetooth LED will light up continuously.
Bluetooth Audio Stream Stutters or Drops Out
A cable is less susceptible to interference than Bluetooth, which has to send
a constant stream of audio data via a radio frequency. To get a good audio
stream without any glitches, it is best to align MOVE 8 and the source
device in line of sight of one another.
Good to know: Your source device may be set up to issue ringtones,
notifi cations and system sounds. The speakers will render these sounds
along with the audio stream if they arrive via Bluetooth, so be sure to
disable these functions on your Bluetooth device.
To learn more about Bluetooth, visit www.bluetooth.org.
MOVE 8 1.1
7