Timer; Weekly Timer - Mitsubishi Electric Mr.SLIM PKA-RP35HAL Manuel D'utilisation

5. Operation
5.5. Airflow direction setting
<To Change the Airflow's Up/Down Direction> (PCA-KAQ, PKA-HAL)
■
With the unit running, press the Airflow Up/Down button
• Each press changes the direction. The current direction is shown at .
• The change sequence and the available settings are as follows.
Remote controller
Swing
Auto
Wired type
Swing
Wireless type
* Note that during swing operation, the directional indication on the
screen does not change in sync with the directional vanes on the unit.
Note:
●
Available directions depend on the type of unit connected.
●
In the following cases, the actual air direction will differ from the direction
indicated on the remote controller display.
1. While the display is showing "STAND BY" or "DEFROST".
2. Immediately after starting heat mode (while the system is waiting for the
mode change to take effect).
3. In heat mode, when room temperature is higher than the temperature setting.
<[Manual] To Change the Airflow's Up/Down Direction>
* The Airflow Up/Down button
PSA-RP•GA
Hold both ends of the vanes and move them to the desired position. Nor-
mally, set the vanes to the horizontal or upward airflow direction for cool-
ing or drying mode, and set the vanes to the downward airflow direction
for heating mode.
* When the airflow direction is adjusted, the
uppermost and lowermost vanes do not move
together with the other vanes.
PCA-RP•HAQ
Move the vane to the desired position. (The position of the vane can be
changed within the range from 10
* If the vane is in the downward position during cooling or dry mode,
condensation may form and drip from the air outlet. If this occurs,
adjust the airflow direction.
* If the cool airflow blows directly onto a flame, cooking table, or food,
and affects the cooking, adjust the airflow direction.

6. Timer

6.1. For Wired Remote-controller
You can use Function Selection of remote controller to select which of
3 types of timer to use:

Weekly timer,

timer.
6.1.1. Weekly Timer
■
The weekly timer can be used to set up to 8 operations for each day
of the week.
• Each operation may consist of any of the following: ON/OFF time
together with a temperature setting, or ON/OFF time only, or tem-
perature setting only.
• When the current time reaches a time set at this timer, the air condi-
tioner carries out the action set by the timer.
■
Time setting resolution for this timer is 1 minute.
Note:
*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same
time.
*2. The weekly timer will not operate when any of the following conditions is
in effect.
The timer feature is off; the system is in an malfunction state; a test run
is in progress; the remote controller is undergoing self-check or remote
controller check; the user is in the process of setting a function; the user
is in the process of setting the timer; the user is in the process of setting
the current day of the week or time; the system is under central control.
(Specifically, the system will not carry out operations (unit on, unit off or
temperature setting) that are prohibited during these conditions.)
8
as necessary.
Display
3 5
1 2 4
1 2 3 4
cannot be used.
° °
up to 45 down.)
Simple timer, or Auto Off
<To Change the Right/Left Air Direction> (Only for PSA-RP•GA type)
Press the louver button as necessary.
• The louver image appears.
Each press of the button switches the setting as follows.
(ON)
(OFF)
Wired remote
controller
No display
During swing operation, the arrow display
(Stop)
move to the left and right.
Wireless remote
controller
No display
During swing operation, the arrow display
(Stop)
move to the left and right.
<[Manual] To Change the Airflow's Left/Right Direction>
* The louver button cannot be used.
• Stop the unit operation, hold the lever of the louver,
and adjust to the desired direction.
* Do not set to the inside direction when the unit is
in the cooling or drying mode because there is a
risk of condensation and water dripping.
Caution:
To prevent falls, maintain a stable footing when operating the unit.
5.6. Ventilation
For LOSSNAY combination
5.6.1. For Wired Remote-controller
To run the ventilator together with the indoor unit:
Press the ON/OFF button
• The Vent indication appears on the screen (at
will now automatically operate whenever the indoor unit is running.
To run the ventilator only when the indoor unit is off:
Press the Mode button until
will cause the ventilator to start.
To change the ventilator force:
Press the Ventilation button
• Each press toggles the setting as shown below.
(Low) (High)
Note:
With some model configurations, the fan on the indoor unit may
come on even when you set the ventilator to run independently.
Operation No.
Day Setting
SUN
C
TEMP.
MENU ON/OFF
BACK B MONITOR/SET DAY
PAR-21MAA R CLOCK OPERATION
<How to Set the Weekly Timer>
1. Be sure that you are at a standard control screen, and that the weekly
timer indicator is shown in the display.
.
). The ventilator
appears on the display. This
as necessary.
ON
WEEKLY
ON/OFF
FILTER
CHECK TEST
CLEAR