Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Mini CiRCulaR Saw with laSeR
your arm to resist kickback forces. Position
your body to either side of the blade, but not
in line with the blade. Position the hand not
holding the saw well away from the travel path
of the saw. Kickback could cause the saw to jump
backwards, but kickback forces can be controlled by
the operator, if proper precautions are taken.
b) when blade is binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material until
the blade comes to a complete stop. never
attempt to remove the saw from the work or
pull the saw backward while the blade is in
motion or kickback may occur. investigate and
take corrective actions to eliminate the cause of
blade binding.
c) when restarting a saw in the workpiece,
center the saw blade in the kerf and check
that saw teeth are not engaged into the
material. if saw blade is binding, it may walk up or
kickback from the workpiece as the saw is restarted.
d) Support large panels to minimize the risk of
blade pinching and kickback. large panels
tend to sag under their own weight. supports
must be placed under the panel on both sides, near
the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
f) Blade depth must be tight and secure before
making cut. if blade adjustment shifts while
cutting, it may cause binding and kickback.
g) use extra caution when making a "plunge
cut" into existing walls or other blind areas.
The protruding blade may cut objects that can cause
kickback.
Safety instructions for Plunge type saw
a) Check guard for proper closing before each
use. Do not operate the saw if guard does not
move freely and enclose the blade instantly.
never clamp or tie the guard with the blade
exposed. if saw is accidentally dropped, guard
may be bent. Check to make sure that guard moves
freely and does not touch the blade or any other
part, in all angles and depths of cut.
b) Check the operation and condition of the
guard return spring. if the guard and the
spring are not operating properly, they must
be serviced before use. Guard may operate
sluggishly due to damaged parts, gummy deposits,
or a build-up of debris.
waRninG: Be sure to shake or vacuum dust and
debris from the guard and base frequently.
c) always observe that the guard is covering
the blade before placing saw down on bench
or floor. an unprotected, coasting blade will
cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it
takes for the blade to stop after switch is released.
SaFetY waRninG FoR YouR
laSeR
warning for class iiia laser, accessible laser
radiation with an irradiance less than or equal to
2.5X10
w cm
-3
-2
LasER RadiaTiON--dO NOT sTaRE iNTO BEaM OR
ViEW diRECTLy WiTh OPTiCaL iNsTRUMENTs
additional safety warning
do not stare directly at the laser beam. a hazard may
exist if you deliberately stare into the beam. Please
observe all safety rules as follows:
1. The laser shall be used and maintained in
accordance with the manufacturer's instructions.
2. Never aim the beam at any person or an object other
than the work piece.
3. always ensure the laser beam is aimed at a sturdy
work piece without reflective surfaces, e.g. wood
or rough-coated surfaces are acceptable. Bright
shiny reflective sheet steel or similar is not suitable
for laser applications as the reflective surface may
direct the laser beam back at the operator.
4. do not change the laser device with a different type.
The manufacturer or an authorized agent must carry
out repairs.
5. Caution: Use of controls or adjustments other
than those specified herein may result in hazardous
radiation exposure.
6. Caution: The use of optical instruments with this
product will increase eye hazard.
Save theSe inStRuCtionS
enG
9
Publicité
Table des Matières
