Publicité
Les langues disponibles
Les langues disponibles
TYCAM 1000 / 2000
TYCAM 1000
Indoor
connected
camera
TYCAM 2000
Outdoor
connected
camera
www.deltadore.com
Power supply
INPUT : 100-240V~ 50-60 Hz 0,3A
OUTPUT : 5V
Consumption
RJ45 Network
Wi-Fi network
Optical sensor/Focal distance
Viewing angle
Minimum light intensity
Night vision
Resolution
Operating temperature and humidity
10% ~ 80% without condensation
Storage temperature and humidity
Degree of protection
Dimensions
1
Presentation
TYCAM 1000
1
3
2
7
8
1. Lens
2. Infrared LED (night vision)
3. RJ45 Network Connector
4. WPS/RESET button
Airtight adaptor
If you associate the camera with the ADSL Box in WIFI mode (see § 5, option 2 or 3), check that the
WIFI connection is operational before fixing the camera in its final location.
2
TYCAM 1000 wall mount
1
A
B
Ê Align the marks A and B then separate the two
Base/Mount parts.
2
9
Ë Secure the mount (9) with screws and plugs.
3
4
1
B
A
3
2
9
8
Ì 1- Align the marks A and B.
2- Insert the base (8) of the camera onto the
mount (9).
3- Turn the base (8) so that the marks A and B
are no longer aligned.
Í Point the camera.
The connection quality of your product may be affected
due to changes on the IP architecture on which it
operates. These changes may involve (the list is not
exhaustive) a change in hardware, software update
or configuration operations, work on your operator's
equipment or any other multimedia devices such as
tablets, smartphones, etc.' Android™ and Google play
are Google Inc trademarks. IOS™ is a Cisco Systems
Inc trademark.
EN
Wi-Fi is a Wireless Ethernet Compatibility Alliance
trademark. WPS (Wi-Fi Protected Setup) is a standard
created by the Wi-Fi Alliance.
Because of changes in standards and equipment, the
characteristics given in the text and the illustrations in
this document are not binding unless confirmed.
You must respect the privacy of neighbours, visitors and
passers-by. It is prohibited to film the public highway.
You also have to inform any persons working in your
home (nurse, baby-sitter, etc.) that they are likely to be
filmed temporarily while working. In this case, you will
have to issue a declaration to the CNIL (French data
protection authority).
WARNING TYCAM 2000 :
This is a Class A product. In a domestic environment,
this product may cause radio interference, in which
case the user may be required to take adequate
measures.
The installation of your camera requires the
presence of a TYDOM installed and connected
to your ADSL BOX.
TYCAM 1000
TYCAM 2000
INPUT : 100-240V~ 50-60 Hz 0,5A
1A
OUTPUT : 12V
2,5 W
Ethernet 10/100Mbps
Wi-Fi IEEE 802.11 b/g/n
1,3" HD CMOS / f 2.8mm
110°
0 Lux (with infrared LED)
Automatic - Range: 8m
Automatic - Range: 20m
Ô Full HD (1920x1080) depending on connection quality
-10°C / +55°C
-10°C / +60°C
10% ~ 80% without condensation
-20°C / +60°C - 0% ~ 90% without condensation
-
76x76x121
TYCAM 2000
4
5
6
1
2
5. Status LED
Sealed connection terminal (option)
6. Power supply
Ref. 6417005
7. Base
8. Mount
3
TYCAM 2000 mounting
1
Wall
A
mounting
B
B
11
12 15
Ceiling
mounting
13
14
11
12
13
14
360°
90°
Ê - Secure the camera base unit firmly in the
chosen position by using screws and plugs
suitable for the nature of the support.
- Loosen screws 11, 12, 13, 14, 15 to point the
camera using a 2.5 mm Allen key.
- Immobilize the camera by tightening the screws
11, 12, 13, 14, 15.
The cable connections must be protected from
bad weather within the building or in a sealed unit
(not supplied).
The power supply unit must be connected within
the building.
2
Ë Screw the antenna (F) to the back of the camera.
4
TYDOM application
1
According to your device, login to Google play or
App Store and check that you have the latest
version of the application.
- Activate the Wi-Fi connection of your smartphone
or your tablet. (your smartphone or tablet must be
on the same Wi-Fi network as your camera)
Ê Open the application and press
the Camera icon
Ë Select "Create an account"
To ensure secure access for your camera, choose a personal password that will be known only to you.
5
Add a camera
Option 1
1A
2,5 W
RJ45
1
Camera
106°
ADSL Box
TYDOM
Connection by network cable
IP 66
(RJ45)
Ê Connect the camera power supply.
97x67x64
Ë Connect the RJ45 network cable.
Ì Wait for about 1 minute (time for the
camera to start up)
Í In the TYDOM application:
- Confirm
- When the camera is found on the
network, press
7
4
3
6
- Name the camera
- Exit the setting mode, the installation is complete.
Note: You have one hour to associate the camera with the application, after this time, unplug then reconnect
the power supply of the camera.
6
Remove a camera
- Open the TYDOM application
- Press the Camera icon
- Select the camera to remove
15
- Press 'Remove camera'
- Confirm
15
360°
Removing a camera requires being connected to
the initial creation account.
Delete the Wi-Fi association
TYCAM 1000
Press the WPS button of the camera for 15
seconds until the red LED flashes once.
TYCAM 2000
Press the WPS/RESET button of the camera for
15 seconds until the infrared LEDs (night vision)
switch on then off.
F
Warning
Please read the information on the protection of
privacy and the associated regulatory measures on :
www.deltadore.com > TYCAM product page.
Create an account
ON
- Fill in the fields:
Last name, first name, user's email address,
password, confirm password, then confirm
When your account is created, a confirmation email
is sent to the email address entered
(If the message does not appear in your mailbox,
check the junk e-mail and spam folders).
.
- Press
- The login screen appears displaying your identifier
and your password.
- Open the TYDOM application
- Press the Camera icon
- Press the setting icon
- Press 'Add a TYCAM camera'
- Select from among 3 installation options:
Option 2
2
1
Camera
2
ADSL Box
WPS
TYDOM
Automatic Wi-Fi association (WPS -
Wi-Fi Protected Setup)
Associate the camera with
the ADSL Box in Wi-Fi
mode, without entering the
security key. (Consult the
documentation of your ADSL
Box).
Ê Connect the camera power supply.
.
Wait for about 1 minute (time for the
camera to start up)
Ë TYCAM 1000 : Press the WPS
button of the camera for 4 seconds:
release: The green LED flashes.
- TYCAM 2000 : Press the WPS
button of the camera for 4 seconds,
release, the infrared LEDs (night
vision) flash.
Ì Press the WPS button of your ADSL
BOX. (maximum period:
2 minutes).
Í In the TYDOM application:
- Confirm
- When the camera is found on the
network, press
.
7
Diagnostic
TYCAM 1000 LED status
.
ADSL bitrate
The ADSL bitrate can vary according to the quality
of the line and its use. The resolution of the camera
must be adapted according to the available bitrate.
In the event of a remote connection problem, change
the camera resolution in the application.
Define the resolution
The ADSL box requires 100 kbit/s for its own
operation.
Example:
You have a upstream bandwidth of 650 kbit/s, set the
resolution of your camera to average quality.
https://www.youtube.com/user/DeltaDoreFrance
2
OK
.
.
Option 3
RJ45
1
Camera
2
ADSL Box
3
TYDOM
Manual Wi-Fi association (without
WPS)
Ê Connect the camera power supply.
Ë Connect the RJ45 network cable.
Wait for about 1 minute (time for the
camera to start up)
Ì In the TYDOM application:
- Confirm
- When the camera is found on the
network, press
.
- Choose your network
- Enter the Wi-Fi key manually.
- Confirm
Í You can unplug the network cable of
your camera.
Only secure networks
are available.
- Red: Not connected to the network
- Green: Connected to the Ethernet
server.
- Flashing green (rapid): WPS
association in progress
- Flashing green (slow): Connected in
Wi-Fi mode.
upstream bandwidth
used by the camera
High
600
Average
300
Low
150
More information is available on the
DELTA DORE video channel:
Publicité
