Selecting The Audio Language; Checking The Digital Signal Strength; Specifications - Dynex DX-R32TV Guide De L'utilisateur

14
To listen to stereo sound:
Notes:
When the television is turned on or a channel is selected, STEREO appears
on the screen, indicating that stereo broadcasting is available. When
only mono broadcasting is available, there is no indicator on the screen.
You can enjoy stereo sound from the left and right speakers.
1 if the broadcasting signal is not strong enough, or clear stereo
sound is not available, press the AUDIO button on the remote
control to change to mono. This should eliminate any noise.
2 Press the AUDIO button again to return to stereo.
To listen to a second audio program (SAP):
1
When the television is turned on or a channel is selected,
SAP appears on the screen, indicating that Second Audio
Program (SAP) is available
2 Press the AUDIO button on the remote control, then select the
desired SAP setting, using the following table as a guide.
Broadcast SAP setting
MONO OFF
ON
STEREO OFF
ON
MONO+SAP OFF
ON
STEREO OFF
ON

Selecting the audio language

When two or more audio languages are included in a digital signal, you
can select one of the audio languages.
To select the audio language:
1 Press TUNER to select the Digital mode.
2 Press MENU/ENTER. The menu screen appears.
3 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select DIGITAL SETUP.
4 Press the VOL + button. The DIGITAL SETUP menu appears.
5 Press the CH + and CH - buttons to select AUDIO LANGUAGE,
then press the VOL + button. The AUDIO LANGUAGE menu
appears.
6 Press the CH + and CH - buttons to select the desired language,
then press MENU/ENTER.
7 Press MENU/ENTER repeatedly until the menu screen is cleared.

Checking the digital signal strength

This television allows you to view the digital signal meter for digital
channels.
Notes:
The signal meter feature is not available for analog channels.
After four minutes, the SIGNAL METER screen returns to normal
television-operation automatically.
To check the digital signal strength:
1 Press MENU/ENTER. The menu screen appears.
2 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select DIGITAL SETUP.
3 Press the VOL + button. The DIGITAL SETUP menu appears.
4 Press the CH + and CH - buttons to select SIGNAL METER, then
press the VOL + button to check the strength of the digital signal.
5 Press MENU/ENTER repeatedly until the menu screen is cleared.
.
Audio display
MONO
MONO
STEREO <->MONO
STEREO <->MONO
MONO
SAP
STEREO <->MONO
SAP
Using the auto shut-off feature
When the auto shut-off feature is on and a station being viewed stops
broadcasting, the television will shut off automatically 15 minutes after
broadcasting stops.
To use the auto shut-off feature:
1 Press MENU/ENTER. The menu screen appears.
2 Press the VOL + and VOL - buttons to select the OPTION menu,
then press the CH + and CH - buttons to select AUTO SHUT OFF.
3 Press the CH + and CH - buttons to select ON or OFF.
4 Press EXIT to return to the normal screen.

Specifications

Design and specifications are subject to change without notice.
Power supply AC 120V, 60 Hz
Power Consumption
Operation 110 Watts
Standby 3 Watts
Chassis Construction
Weight 114.7 lbs. (52.0 kg)
Width 32.9 inches (836 mm)
Height 21.69 inches (551 mm)
Depth 25.79 inches (655 mm)
Inputs
VIDEO 1 V (p-p)/75 ohms
AUDIO –8 dBm/50k ohms
S-VIDEO Y: 1 V (p-p), 75 ohms
C: 0.286 V (p-p), 75 ohms
COMPONENT Y: 1 V (p-p), 75 ohms
PR: 0.7 V (p-p), 75 ohms
PB: 0.7 V (p-p), 75 ohms
Output
AUDIO –8 dBm/50k ohms
Other
Antenna input VHF/UHF In 75 ohm coaxial
Picture tube 32 inches (800.1 mm diagonal)
Tuner type NTSC Standard
ATSC Standard (8VSB), QAM
Receiving channels VHF 2-13
UHF 14-69
CABLE TV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Speakers 2 inches (50.8 mm) x 3-1/2 inches
(88.9 mm), 8 ohm x 2
Sound output power 1.0 W + 1.0 W
Specifications