Safety Instructions - Wolfcraft 5019000 Notice D'utilisation

This cutting stand is an aid for cutting work (exclusively for metal)
with a one-hand angle grinder. It is suitable for use with most
angle grinders with a disc size of Ø 115 or Ø 125 mm. Carefully
read this instruction manual and especially the safety instructions
before using the cutting stand.
Assembly instructions
Refer to illustration (A) and the detailed photos (B - I) when as-
sembling the stand.
You require the following for the assembly work: open-jawed
spanners (SW 8, SW 10, SW 14, SW 17), Allen screws (5 mm,
6 mm) and a slotted screwdriver (5 mm).
• Mount the swivel arm (2) to the base plate (1) using the Allen
screws (3) and the washers (4).
• Now mount the handle (6) onto the swivel arm (2) with the
matching counter nut.
• Now mount both of the retainers (9) onto the swivel arm (2)
with the spacers (10) and the Allen screws (11). These two
connections are only loosely mounted.
• Insert the two adjustment screws (5 and 7) in the swivel arm
(2) recess, together with the adjustment nuts.
• Now mount the protective cover (8). To do so, insert the cover
hoop in the corresponding opening in the swivel arm (2). Now
fasten the hoop in place with the screw (13) and the nut (14).
• Now mount the angle grinder with the cutting disc between
both of the retainers (9). To do so, use the matching mounting
material (16) in the sizes M10, M8 or M6 as shown.
• Align the angle grinder between both of the retainers (9) and
fix the angle grinder in place with the screws, locking nuts and
the spacer (15). Mounting material of the sizes M8 and M6
require the insertion of additional plastic sleeves into the
retainers (9).
• Adjust the two adjustment screws (5 and 7) so that the angle
grinder is positioned perpendicular to the base plate (1). Now
screw the two washers and the nuts onto the adjustment
screws and tighten them. Now tighten the two Allen screws
(11).
• After loosening the Allen screws (3) slightly, adjust the swivel
arm (2) so that the cutting disc immerses into the cutting gap
in the base plate (1), now retighten both of the screws.
• Now clamp the mains cable of the angle grinder in the cable
holder (12).
• After completing the assembly, switch the angle grinder
on for a few seconds and then switch it off again.
Re-check the tightness of all of the screws and the
screwed connections.
• Your cutting stand is now ready for use.
Declaration of Conformity pursuant to Directive 2006/42/EC
on Machinery, Annex II A
wolfcraft GmbH in D-56746 Kempenich, Wolff-Str. 1, hereby
declares that this product (5019.000) conforms to Directive
2006/42/EC on Machinery.
Kempenich, 08.03.2010
Michael Bauseler
Authorized CE representative
(Management/Technology/Logistics; wolfcraft GmbH)
G

Safety Instructions

• It is imperative that you adhere to the information in the
instruction manual for the angle grinder used. This device
must correspond to the VDE standards. Only devices with a
CE symbol are to be used.
• Keep children away from the workplace and also keep the tools
out of the reach of children.
• Always wear protective goggles, ear protection, protective
gloves and a mouth or nose protection respectively.
• Wear suitable working clothes; do not wear any wide clothing
or jewellery as they could be caught up in moving parts.
Non-slip shoes are recommended. Wear a hair net if you have
long hair.
• Before use, ensure that the device is correctly and securely
mounted in the retainer.
• Never stop the cutting disc with your hands or with objects.
• Mount the cutting stand on both of the mounting perforations
in the base plate (1) on the workbench. Ensure that the bench
and the stand are securely positioned.
• Ensure that the workplace is clean and well illuminated.
• Ensure that you do not come into contact with the cutting disc
when working. RISK OF INJURY!
• Always use the protective cover (8).
• Only use the cutting stand with an angle grinder which is
equipped with the suitable metal protective cover around the
cutting disc.
• Position this protective cover so that the cutting disc runs freely
in the open part and so that the protective cap is unable to
make contact with the work piece.
• Cutting work generates sparks. Ensure that no flammable
materials are in the working area. Sparks can damage paint,
glass and other surfaces. Do not wear any nylon or polyester
clothing, but suitable non-flammable work clothes.
• Ensure that the mains cable does not protrude into the working
area of the disc or where sparks are flying. Always insert the
mains cable of the angle grinder in the cable holder (12).
• Ensure that the work piece is correctly fixed in position
between the two clamping jaws and is firmly positioned on
the base plate.
• Do not use work pieces which are too large to be fixed in
position between the two clamping jaws.
• Store the cutting stand in a dust-free and dry place.
• Regularly inspect the firm seating of all of the screws before
and during use. Regularly inspect the stand for signs of
damage. Screws can become loose during use due to vibration.
Do not use the cutting stand if you detect any damage.
• Ensure that the cutting disc of your angle grinder is mounted
perpendicular to the base plate.
• Only use cutting discs and no roughing discs.
• Also regularly inspect the cutting disc of your angle grinder for
signs of damage. Under no circumstances should you use a
disc if you should determine any dents, notches or other forms
of damage.
• Always remove the plug of your angle grinder from the socket
before carrying out any cleaning or adjustment work on your
cutting stand.
• Never place you hand in the working area of the cutting disc.
• Always observe the cutting depths as there is otherwise the risk
of damaging your workbench.
• Always remove the plug when not using the stand.
5