For Your Safety; Intended Use - Flex LST 803 VR Mode D'emploi

Bush hammering machine LST 803 VR, LST 1503 VR

For your safety

t^okfkd>
_ÉÑçêÉ=ìëáåÖ=íÜÉ=éçïÉê=íççäI=éäÉ~ëÉ=êÉ~Ç=
~åÇ ÑçääçïW
íÜÉëÉ=çéÉê~íáåÖ=áåëíêìÅíáçåëI
–
íÜÉ=ÒdÉåÉê~ä=ë~ÑÉíó=áåëíêìÅíáçåëÒ=
–
çå íÜÉ Ü~åÇäáåÖ=çÑ=éçïÉê=íççäë=áå=íÜÉ=
ÉåÅäçëÉÇ ÄççâäÉí=EäÉ~ÑäÉíJåçKW=PNRKVNRFI
íÜÉ=ÅìêêÉåíäó=î~äáÇ=ëáíÉ=êìäÉë=~åÇ=íÜÉ=
–
êÉÖìä~íáçåë=Ñçê=íÜÉ=éêÉîÉåíáçå=çÑ=~ÅÅáÇÉåíëK
qÜáë=éçïÉê=íççä=áë=ëí~íÉ=çÑ=íÜÉ=~êí=~åÇ=Ü~ë=ÄÉÉå=
ÅçåëíêìÅíÉÇ=áå=~ÅÅçêÇ~åÅÉ=ïáíÜ=íÜÉ=~ÅâåçïJ
äÉÇÖÉÇ=ë~ÑÉíó=êÉÖìä~íáçåëK=
kÉîÉêíÜÉäÉëëI=ïÜÉå=áå=ìëÉI=íÜÉ=éçïÉê=íççä=ã~ó=
ÄÉ=~=Ç~åÖÉê=íç=äáÑÉ=~åÇ=äáãÄ=çÑ=íÜÉ=ìëÉê=çê=~=íÜáêÇ=
é~êíóI=çê=íÜÉ=éçïÉê=íççä=çê=çíÜÉê=éêçéÉêíó=ã~ó=
ÄÉ=Ç~ã~ÖÉÇK=
qÜÉ=éçïÉê=íççä=ã~ó=ÄÉ=çéÉê~íÉÇ=çåäó=áÑ=áí=áë
~ë=áåíÉåÇÉÇI
–
áå=éÉêÑÉÅí=ïçêâáåÖ=çêÇÉêK
–
c~ìäíë=ïÜáÅÜ=áãé~áê=ë~ÑÉíó=ãìëí=ÄÉ=êÉé~áêÉÇ=
áããÉÇá~íÉäóK

Intended use

This bush hammering machine is designed
– for commercial use in industry and trade,
– for roughening and milling stone surfaces
with tools which are offered by the
manufacturer for this power tool,
– for use on staircases and surfaces.
Safety instructions for bush
hammering machines
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 This electric power tool must be used
with the appropriate accessories as
a refurbishing milling machine.
Read all safety warnings, instructions,
illustrations and specifications provided
with this power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or
serious injury.
 This electric power tool is not suitable
for use with wire brushes, or for polishing,
sanding with sandpaper, renovation
sanding or cut-off grinding.
Operations for which the power tool was not
designed may create a hazard and cause
personal injury.
 Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can be attached
to your power tool, it does not assure safe
operation.
 The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
 The outside diameter and the thickness
of your accessory must be within
the capacity rating of your power tool.
Incorrectly measured insertion tools cannot
be adequately shielded or controlled.
 Sanding discs, sanding pads or other
accessories must fit exactly on the grin-
ding spindle of your electric power tool.
Insertion tools, which do not fit exactly on
the grinding spindle of the electric power tool,
rotate unevenly, vibrate violently and may
result in loss of control.
15