Télécharger Imprimer la page
Velleman COPTERMECH Mode D'emploi

Velleman COPTERMECH Mode D'emploi

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Liens rapides

1. Introduction & Characteristics
Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use.
• Familiarise yourself with the operation of transmissions steered through gears or pulleys.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder "KNS4 – Figures"!!!
2. Parts List
Part n°
Quant.
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
10
8
11
2
3. Prepunched Boards (see "KNS4 – Figures
4. Assembly (see also "KNS4 – Figures
Fig. 4 : Insert part n°20 in the hole on board n°2 and mount the motor holder according to fig. 4.
Fig. 5 : Insert part n°20 (x 8) in boards n°1 & 4. Insert part n°7 between boards 1 & 4. Insert 2 x part n°15 in board
n°4 and through the pulley (part n°10). The metal shafts come out the other side of board n°1. Remember
to put the rubber bands (parts n°18 & 16) on the pulley before inserting the metal shaft. Another part n°15
goes through boards n°1 & 4.
Fig. 6 : Cut part n°5 to precisely 32mm. Insert part n°20 in board n°5 first, then put metal shaft n°14 through board
n°5. Mount part n°5 & 8 according to figure 6. Attach board n°5 to boards n°1 & 4 with part n°19.
KNS4
KNS4 – COPTERMECH
Description
motor holder
battery holder
motor with wire
slide switch with wire
plastic tube (L : 15cm)
metal shaft (2 x 40mm)
pinion gear
face gear 36T/14T (white)
pulley 19.5 x 2mm (blue)
pulley 15 x 2mm (yellow)
pulley 24 x 2mm (white)
)
"
Part n°
Quant.
12
2
13
3
14
3
15
3
16
1
17
1
18
4
19
7
20
15
21
11
22
26
)
"
1
Description
fixing plate
PVC tube (1.5 x 15mm)
metal shaft (2 x 90mm)
metal shaft (2 x 70mm)
belt (black) (126 x 1mm)
rubber band (35mm, red)
rubber band (40mm red)
fixing plate (L-shaped)
nylon pad
nylon pad
self-tapping screw
VELLEMAN

Publicité

loading

Sommaire des Matières pour Velleman COPTERMECH

  • Page 1 KNS4 – COPTERMECH 1. Introduction & Characteristics Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use. • Familiarise yourself with the operation of transmissions steered through gears or pulleys. • Easy to build, no glue or soldering required.
  • Page 2 Note : The specifications and contents of this manual can be subject to change without prior notice. KNS4 – COPTERMECH 1. Inleiding en Kenmerken Dank u voor uw aankoop ! Lees deze handleiding aandachtig voor u het toestel in gebruik neemt.
  • Page 3: Problemen En Oplossingen

    • De assen (n°6, 14 & 15) in de nylon kraagringen (n°20 & 21) moeten kunnen bewegen zodat de katrollen en de wielen ongehinderd kunnen draaien. KNS4 – COPTERMECH 1. Introduction et Caractéristiques Nous vous remercions de votre achat ! Lisez la notice présente attentivement avant la mise en service du KNS4.
  • Page 4: Liste Des Pièces

    Fig. 12 : Vissez le porte-piles (n°2) sur le dessous de panneau n°2. Guidez les fils à travers panneau n°2 et connectez-les au moteur et au commutateur (voir fig. 16). Fig. 13 : Cette figure nous montre l’état actuel du KNS4. KNS4 VELLEMAN...
  • Page 5: Problèmes Et Solutions

    • Remarquez que les axes (n°6, 14 & 15) dans les canons en nylon (n°20 & 21) doivent tourner avec souplesse pour garantir un mouvement souple des poulies et des roues. KNS4 – COPTERMECH 1. Einführung und Eigenschaften Wir bedanken uns für den Kauf des KNS4 ! Lesen Sie diese Bedienungsanleitung vor Inbetriebnahme sorgfältig durch.
  • Page 6: Introducción Y Características

    • De Achsen (n°6, 14 & 15) in den Nylonbuchsen (n°20 & 21) müssen bewegen können, so dass die Riemen und Räder ungehindert drehen können. KNS4 – COPTERMECH 1. Introducción y Características ¡Gracias por haber comprado el KNS4! Lea cuidadosamente las instrucciones del manual antes de montarlo.
  • Page 7: Lista De Piezas

    • Note que todos los ejes (n°6, 14 & 15) en los cañones de nylon (n°20 & 21) deben poder girar libremente a fin de garantizar un movimiento suave de las poleas y las ruedas. Observación : Se pueden modificar las especificaciones y el contenido de este manual sin previo aviso. KNS4 VELLEMAN...

Ce manuel est également adapté pour:

Kns4