Dexter Laundry T-50 Manuel De L'utilisateur page 28

TEMPORARY REVERSING DRYER CONTROLLER PROGRAMMING
REQUIREMENTS: Dry a load, in reverse mode, with 40 minutes of actual heat at 185°F and two minutes of cool
down.
The following procedure will show you how to temporarily modify the existing dry cycle 5 program for one cycle of
drying. It is based on the assumption that the factory defaults have not been permanently changed. If they have
been changed, the steps of this procedure will be the same, but the values that are displayed will be different. The
amount of times that the UP or DOWN touch pad switches of the dryer controller must be pressed and released
may also be different.
If you want the change to be permanent, go to the "PERMANENT REVERSING DRYER CONTROLLER
PROGRAMMING" section of this manual.
1) After the load has been placed in the dryer, press and release either the UP or DOWN touch pad switch on
the dryer controller until the L.E.D. for dry cycle 5 is illuminated.
2) Press and release the CYCLE touch pad switch on the dryer controller. You will see the number "25" on the
dryer controller display. The programming L.E.D. and dry time L.E.D. will be illuminated.
3) Press and release the UP touch pad switch on the dryer controller 17 times so that the display will show a
flashing "42". When the UP touch pad switch is pressed the first time, the number "26" will be flashing on
the dryer controller display. Each number after that will also flash.
4) Now, press and release the SELECT/ENTER touch pad switch on the dryer controller. The number "42"
will stop flashing, the dry time L.E.D. will switch off, the dryer controller display will now show "175", the
temperature L.E.D. will illuminate, and the programming L.E.D. and dry cycle 5 L.E.D. will remain on.
5) Press and release the UP touch pad switch on the dryer controller two times so the controller display will
show a flashing "185". Each press of the UP touch pad switch will increment the temperature by five
degrees.
6) Now, press and release the SELECT/ENTER touch pad switch on the dryer controller. The number "185"
will stop flashing, the temperature L.E.D. will switch off, the dryer control display will now show a number "2",
the cool down L.E.D. will illuminate, and the programming L.E.D. and dry cycle 5 L.E.D. will remain on.
7) Press and release the SELECT/ENTER touch pad switch on the dryer controller, since the desired cool
down time is two minutes. After you press the SELECT/ENTER touch pad switch, the cool down L.E.D.
will switch off, the dryer controller display will show "nrEv", the reversing L.E.D. will illuminate, and the
programming L.E.D. and the cycle 5 L.E.D. will remain on.
8) Press and release either the UP or DOWN touch pad switch on the dryer controller once. A flashing "rEv"
will appear on the dryer controller display and the reversing L.E.D will start to flash. Each press and
release of either the UP or DOWN touch pad switch will toggle between the reversing mode ("rEv") and
the non-reversing mode ("nrEv").
9) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the
SELECT/ENTER touch pad switch is pressed and released, the programming L.E.D. and the reversing
L.E.D. will switch off, the dry cycle 5 L.E.D. will remain on, and the flashing "rEv" will stop flashing and
remain on.
You are now ready to start the new dry cycle. This new dry cycle will be in effect for one dry cycle only.
After the dry cycle is done, or if the STOP touch pad switch on the dryer controller is pressed and released
twice, consecutively, the cycle 5 program will revert to the factory default settings.
If you press the START touch pad switch on the dryer controller, the controller display will change from
the "rEv" to the number "42" and dry cycle 5 will begin.
8514-262-001 REV G PAGE 28
EXAMPLE
PROCEDURE: