Air Filter Maintenance; Spark Plug Maintenance; Storage; Labels - Texas LX550TG Manuel De L'utilisateur

Air filter maintenance

Please inspect and clean the air filter on a regular basis. If
the filter has not been cleaned for a longer period, this will
have influence on the engines power take-off and the
exhaustion. See fig. 17.
1. Clean around the air filter before it is removed.
2. Carefully remove the paper filter and check it. Brush
it with a soft brush. If it is very dirty, it must be
changed. Take care that no dirt gets into the intake
of the engine.
3. Wash the black foam element on the right side in
warm soapy water.
4. Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly with oil. Carefully squeeze out any
surplus oil. Remount the element.
5. Check that all parts are fitted correctly and the cover
closed as shown in the picture.

Spark plug maintenance

•
Remove the spark plug cap.
•
Brush away any dirt and deposit of the spark plug.
•
Loosen the spark plug using a spark plug socket.
•
Check the insulation is intact.
•
Clean the spark plug using a wire brush.
•
Measure the electrode gap 0.7–0.8 mm.. Avoid
damaging the electrode.
•
If it is damaged, replace it with a new one.
•
Refit the spark plug.
•
Refit the spark plug cap.

Storage

•
If the machine is likely to be stored unused for
prolonged periods, follow the instructions below.
This will ensure longer machine lifetime.
•
Use a garden hose to wash off soil and dirt.
Remove any grass, etc. from the rotor shaft. The
chassis number should only be cleaned with a
damp cloth to avoid unnecessary wear. Avoid using
a high-pressure washer during cleaning.
•
Wipe the tiller with a damp cloth so that all surfaces
are clean. Wipe the surfaces down with an oily cloth
to prevent rust.
•
Always store the machine in a dry, clean location.

Labels

See description fig 18.

Troubleshooting

The motor will not start
1. Check the fuel control is set correctly.
2. Check the spark plug.
3. Check there is fresh gas in the tank.
4. See separate motor instructions for further
troubleshooting.
The motor is not running smoothly
1. Ensure the throttle control is not set to max.
2. Check there is fresh gas in the tank.
The blades will not rotate
1. Check for stones lodged between the blades.
2. Release any stones by removing the blades.
3. Check the cables are in good working order and
fitted correctly.
4. Check the belt is in good working order and fitted
correctly.
5. Ensure the belt tensioner is adjusted correctly.
The blades will not stop
1. Stop the engine and contact your dealer.

Noise, vibration and precautionary measures

1. Long-term exposure to noise levels exceeding 85
dB (A) are damaging. Always use ear defenders
when the machine is being used.
2. Reduce the running speed of the motor to reduce
vibration and noise levels.
3. To reduce noise levels further, only use the machine
in an open environment.
4. Vibrations can be reduced further by holding the
handle firmly.
5. To avoid disturbing others, the machine should only
be used during the daytime.
6. Always wear close-fitting work clothes, hard-wearing
work gloves, ear defenders and non-slip boots with
steel toecaps.
7. Take a 30-minute break every 2 working hours.
Specification
Machine
Motor model
Total width
Total height
Total length
Net weight
Blade speed
(rpm- forward)
Blade speed
(rpm-reverse)
Operating
width
Engine
Type
Capacity
Max power
kW / rpm
Fuel
Fuel capacity
Lubricating oil
Lubricating oil
capacity
Start system
Spark plug
9
LX 550 TG
Texas Powerline
TG585
60 cm
120 cm
140 cm
51 kg
91 /min
55 /min
58 cm
TG585
4-stroke, air-cooled 4-stroke, air-cooled
OHV, 1 cylinder, gas OHV, 1 cylinder, gas
163 cc
3.0kW / 3600
Unleaded gas
1 (L)
SAE30
0,6 (L)
Recoil
DENSO W16EPR-U DENSO Q16PR-U:
(10011033)
LX 550B
B&S
650E
60 cm
120 cm
140 cm
53 kg
91 /min
55 /min
58 cm
B&S 650E
190 cc
2,61 kW / 3600
Unleaded gas
1,4 (L)
SAE30
0,6 (L)
Recoil
(10011004)