Chapin 6300 Mode D'emploi

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do
not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible
explosion. Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve
shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there
is pressure in sprayer. Never stand with face or body over top of tank when pumping or loosening
pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never pres-
surize sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Re-
place parts only with manufacturer's original parts. Never spray flammable, caustic, acidic, chlorine,
bleach or other corrosive solutions or heat, pressure, or gas producing chemicals. Always read
and follow chemical manufacturer's instructions before use with this sprayer as some chemicals
may be hazardous when used with this sprayer.
WARNING: Handling the brass parts of this product will expose you
to lead, a chemical known to the State of California to cause birth
defects and other reproductive harm. Wash hands after handling.
DIRECTIONS FOR ASSEMBLY: Remove bolt with nut from handle, and
turn handle upright; insert bolt in upper hole, and screw on nut tightly. If
this height is not convenient, remove three bolts and lower upper part of
handle to convenient height, reinserting two bolts and tighten nuts securely.
Handle may also be reversed, with curved part of upper handle directed
backwards, if desired.
Parts, Piezas, Pièces
6-6143 1-2619-1 6-6000 6-1866
Hose Extension Nozzle Shut-off Handle
Manguera Clip Tobera Mango de cierre
Tuyau Manguera Buse Poignée du robinet
Tuyau
6-7711
Extension wand, Vara de extensión, Rallonge
3-7019 3-7535-1 3-8988-1
Pump Barrel Assembly Pump Assembly Rod Assembly
Asamblea de barril de la bomba Asamblea de la bomba Asamblea de Rod
Assemblée de baril de pompe Assemblée de pompe Assemblée de Rod
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-4627
1. Hose to Tank
1A
Hose Barb
2. Nozzle
2A
Sk-1154-1
Attach nozzle to shut-off handle or extension wand.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration
indicates possible tank weakening and could result in explosive bursting under pressure. If any of
these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc.,
as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger
10-20 strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and
proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.
If any of these conditions are found, replace affected part with original manufacturer's part
before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank
and tighten securely.
5. Pressurizing and Spraying
3-2435
Cart Assembly
5A
Asamblea del carro
Assemblée de chariot
TO LOCK HANDLE: Push handle down to depress coil spring and turn handle 1/4 turn
clockwise, then allow handle to raise into lock position.
2-1063-1 (A) R0911
Make sure hose is pushed all the way to
the tank. Make sure hose clamp is tight
and below the hose barb. Turn clockwise
with a screwdriver to tighten.
2B
5B
5. Pressurizing and Spraying, continued
5C
TO LOCK PUMP: Place pump prongs down into slots in funnel,
turn clamp clockwise to furthest position under bottom slot, then
turn handle clockwise until tightly locked and sealed in place.
5D
TO UNLOCK PUMP: Turn handle counterclockwise until
3-prong clamp is loose. Then rotate clamp counterclockwise to
stop and lift out.
5E
TO RELEASE HANDLE: Push down to depress coil spring
and turn handle counterclockwise 1/4 turn, then lift handle.
5F
Pump until you feel resistance.
6. Fatigue-Free Spraying
For constant spraying, push down on shut-off
handle and move locking mechanism away from
you. To release, squeeze handle and move the lock-
ing mechanism back towards you.
7. To Release Pressure
1 Do: With pump facing away, turn locked handle counterclockwise until air begins to
escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the
wand and nozzle are thoroughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.