Safety Precautions - Sigel Artverum GL 235 Instructions De Montage Et Consignes De Sécurité

EN
CONTENTS
Mounting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Storing this user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Use & cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Magnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Disposal and recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Distance between drill holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
STORING THIS USER GUIDE
This user guide will help you to make the best use of your new magnetic glass board. In addition to this, it contains important information
about how to safely mount and use your magnetic glass board.
Read this user guide and make sure you have understood it before mounting and using your new magnetic glass board.
Store this user guide near your magnetic glass board. If the magnetic glass board is passed on to another user, make sure that person also
receives this user guide.

SAFETY PRECAUTIONS

The Artverum Magnetic Glass Board is made of tempered safety glass tested to EN 12150-1.
1 | Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
2 | When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as
stone or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted
and do not remove the protective corners until it is attached to the wall.
3 | The magnetic glass board should only be mounted on an even, solid wall.
4 | Two people are required to mount the board.
5 | In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling templates. You will find the measure-
ments for the relevant distances between drill holes on page 16 and on our website at www.sigel-office.com/en-gb/mounting-instructions
SIGEL GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
MOUNTING
1 | The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling templates make it simple to mark the
position of the drill holes. The wall fixings
SIGEL logo should be facing outwards (fig. I).
Tip: Please use a spirit level to check that the wall fixings
The wall fixings have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall
4 4
fixings vertically or horizontally as required. Then tighten the screw again.
4 4
2 | Two people are required to mount the magnetic glass board. An additional handle
150x100 cm, 180x120 cm, 200x100 cm and 240x120 cm formats.
Tip: to simplify the positioning of the board, mark the wall lightly in pencil (fig. II), e.g. to indicate the width of the board. Likewise, you can mark
the position of the corners and the mounting fittings (for distances see pg. 16).
To mount the board on the wall, hold the bottom edge with one hand and the side with the other. If mounting one of the large boards, use the
handle to support the bottom edge (Fig. III) and grip the side of the board firmly with your other hand. The magnetic glass board
6 6
mounted onto the wall fixings
has two openings (fig. V); the wall fixings
hung in portrait or landscape format.
Place the mounting fittings
5 5
board downwards so that the wall fixings
Make sure that the magnetic glass board is mounted on all fittings and check that the board is securely in place before letting go. Silicon pads
on the back of the board keep it steady while it is being written on.
are screwed securely to the wall using anchors
4 4
4 4
(fig. IV). There are four or six mounting fittings
4 4
must always be slotted into the top opening rather than the side opening, whether the board is
4 4
on the back of the board over the wall fixings
click into the mounting fittings
4 4
are lined up straight.
on the back of the board for this. Each mounting fitting
5 5
so that the wall fixings
4 4
(fig. VI) and the board is mounted securely.
5 5
6
and screws . The side of the board with the
2 2 3 3
for each person is included for the boards in the
6 6
are in the centre (fig. V). Now slide the
4 4
is then
1 1
5 5