Honeywell Intermec CK70 Mode D'emploi page 2

This product complies with IEC 62471 for LED safety.
This product may use any of the following scan engines:
• EX25
• EA30
• N5603
The camera assembly with flash is classified as: Risk Group 2.
Caution: When using the camera flash, keep the camera flash LED at least 317 mm (12.5 in) away from the subject's eyes. Otherwise
serious damage to one's eyes may occur.
U.S.A. Digital Emissions Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Compliance
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3 (B)
802.11a Radio Precaution Statement (North America)
Caution: 802.11a wireless LAN 5150 to 5250 MHz (5.15 to 5.25 GHz) (5 GHz radio channels 34 to 48) is restricted to indoor operations
to reduce harmful interference to co-channel Mobile Satellite System (MSS) operations.
Caution: The maximum antenna gain permitted for devices in the bands 5250 to 5350 MHz and 5470 to 5725 MHz shall comply with the
e.i.r.p. limit.
Caution: The maximum antenna gain permitted for devices in the band 5725 to 5825 MHz shall comply with the e.i.r.p. limits specified for
point-to-point and non point-to-point operation as appropriate.
Caution: Be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250 to 5350 MHz and 5650 to
5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
For Users in Europe
Scan Engine and Camera Flash Compliance and Precautions
This product complies with IEC 60825-1 / EN 60825-1.
When the EX25 scan engine is installed, the device is a Class 1 laser product.
When the EA30 or N5603 scan engine is installed, the device is a Class 2 laser product with a maximum output of 1 mW at 630-680 nm.
Caution: Use of controls or adjustments, or performance of procedures other than those specified herein, may result in hazardous laser
light exposure.
Note: There are no controls or adjustments provided for routine operation or maintenance of the product. There are no user-serviceable parts inside
this product.
If applicable, this product will be provided with a set of laser safety labels illustrated on the last page of this document. If the proper label language
is not installed on the device, locate and apply the appropriate label over the existing label.
This product complies with IEC 62471 for LED safety.
This product may use any of the following scan engines:
• EX25
• EA30
• N5603
2