Philips Universal PM3S Mode D'emploi page 23

Direct
Code Entry
1. Press and hold the
CODE SEARCH
button until the red indicator stays
on, then release the
CODE SEARCH
button.
2. Press and release the desired Mode
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
3. Enter the 4 digit code from the code
tables. Note: after a valid code entry,
the red indicator turns off. For an
invalid code, the red indicator
flashes.
4. With your device on, press
CHANNEL UP. If the device
responds, no further programming is
required. Note: If some buttons do
not operate your device, try one of
the other codes for your brand.
Code Search (by Brand)
Lets you search for a code for a specific
.
Brand within the Code Library for a
particular manufacturer.
1. Turn on the device
(TV,
VCR, etc.) to
be controlled.
2. Press and hold the
CODE SEARCH
button until the red indicator remains
on, then release the
CODE SEARCH
button.
3. Press and release the desired Mode
button (TV, VCR, etc.). The red
indicator blinks off once.
4. Press and release the numeric button
(0-9) corresponding to desired
Manufacturer (see table below).
Note, pressing " 0 performs a full
library search same as Device Library
Code Search Method.
5.
Press the CHANNEL UP button ((or
POWER or PLAY (VCR only))
repeatedly until the device to be
controlled changes channel.
6. Press and release MUTE to install
the code.
Note, when all codes under a Brand
have been searched the red indicator
flashes rapidly for 3 seconds.
Code Search (by Device)
If after trying "Direct Code Entry" or
"Code Search (by Brand)" your device
does not respond, or if your brand is not
listed, try doing a device search of the
code library for your code by following
the steps below.
1. Manually turn on the device
(TV,
VCR, etc.) to be controlled.
2. Press and hold the
CODE SEARCH
button until the red indicator stays
on, then release the
CODE SEARCH
button.
3. Press and release the desired Mode
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
4. Press the CHANNEL UP button
repeatedly (up to 300 times) until
the device to be controlled changes
channel. The red indicator blinks,
then stays lit.
5. Press and release MUTE to install
the code.
Most users will want to store VCR
codes under the VCR button, Cable
codes under Cable, etc. If you want to
store a VCR code under Cable, etc., first
follow the procedure for Direct Code
Entry and press Cable in step 2 of
Direct Code Entry, then enter ANY
VCR code in step 3 of Direct Code
Entry. Then follow the steps above for
Brand Search or Complete Search.
Brand Search Table
Look up your brand in the appropriate
column (TV, VCR, etc.) in the table
below. Look for the digit (1, 2, 3, etc.)
that applies to your brand, and enter it
in step 4 of "Code Search @y Brand)."
Dielt
I
T V
I
VCR/DVD/DVR
I
C A B L E
I
SATIDBS
1
I
RCA, GE,
I
RCA, GE.
I
Scientific Atlanta
I
RCA. GE.
I
RCA. GE. proscan
. .
Proscan Proscan Proscan. Pioneer
2 Zenith Z e n ~ t h , Apex Jerrold
Zcn~th, Gemmi Zenith
'
3
Philips, Maranlz, Ph~lips, Tocorn. General Philips, Marantz. Philips,
Magnavox Magnavox Instrument,
Magnavox Magnavox
4 Sony. Panasonic. Sony. Panasonic. RCA. GE. Sonv, Panasontc, Sonv. Panasonic.
Sharp. Toshiba. Sharp. Toshiba. Proscan, Pioneer Sharp, Toshlba,
I
I
Dacwoo
1
Dacwoo. Yamaha.
I
I