Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
This product is a multifunctional device, combining
emergency start-up of car battery, lighting, SOS
warning, charging mobile devices, powering to 12V
vehicle-mounted equipment five functions in one.
CAUTIONS
1. Just use the jump starter to start a 12V vehicle.
2. When use the jump starter to start a car, check the
remaining capacity is at least 3 LEDs on and the
machine is cool down.
3. Disconnect the clamp from jump starter and
vehicle immediately after every start attempt.
Do not use it to start the vehicle frequently. Each
attempt allow at least 30s to rest.
4. Please charge the jump starter at least once a
month and do not charge it when it is hot or
immediately after each use.
5. Do not allow the mental teeth of the red clamp to
touch the black clamp.
6. Keep the jump starter from children.
7. Do not dissemble the jump starter.
8. Do not insert foreign objects into any input or
output ports.
9. Do not put the jump starter in extreme
environment where the temperature and humidity
is high.
10. If you find the jump starter inflates, please stop
use and send it to the authorized service center.
11. The device shall be stored indoors and protected
from the elements.
12. The unit shall not be charged outdoors.
13. When in use, steps should be taken to reduce the
exposure to rain, sleet, snow, and the like.
1. CHARGING
NOTE: Upon initial use, your JUMP STARTER
should be charged for a minimum of 4 hours.
CHARGE STATUS INDICATION
Press the Power Button one time to see the unit's
state of charge. The unit's state of charge status is
indicated by four LED indicators below the Power
Button, as follows:
One LED on= Recharge Immediately
Two LEDs on= 25-50% Charge – Charge soon
Three LEDs on= 50-75% Charge – Charge if using as
a jump starter
Four LEDs on= At or near full charge
NOTE: When starting up as a battery, it is
recommended that the jump starter be in or near
100% charge state, at least three grids of charge.
CHARGING INSTRUCTIONS (SEE FIGURE A1)
1. Connect the pin jack to the jump starter through
the input port.
2. Connect the USB power connector to the AC
adapter.
3. Plug the AC adapter into the power supply.
12V Multifunction Jump Starter with LED
Lights
CHARGING WITH THE CAR CHARGER (SEE
FIGURE A2)
1. Connect the car charger and the car charging
cable, then connect the jump starter through the
cable.
2. Insert the car charger into 12V car receptacle.
NOTE: The LEDs will turn on successively to
indicate charging progress. When all LEDs are lit
solid, the unit has reached full charge.
2. STARTING THE VEHICLE
NOTE: When starting the vehicle, make sure that
the unit is charged such that the unit's Status
Display shows 3 LEDs when the Power Button is
depressed.
1) Connect the clamp set to the vehicle ignition
port. Be sure that the cable connection is
fully engaged and secure. Upon connection,
the clamp will then light a flashing blue LED,
indicating the unit is in standby mode. (See
Figure B1)
2) Turn ignition off before making vehicle
connections.
3) Clamp the positive (red +) clamp to the positive
terminal on the vehicle battery, and clamp the
negative (black –) clamp to the negative terminal.
Once connected, the clamp will turn on solid
green. (See Figure B2)
NOTE: If you need to start more than once, pay
attention to the unit's Status Display (at least 3
LEDs on).
If the unit lights on or beeps, check the New
Smart Cable Specification.
NOTE: You have 10 seconds to start the vehicle
(counting from the moment the clamps are
connected correctly into the Jump Starter) or the
unit will return to standby mode.
4) Start the vehicle (turn on the vehicle ignition).
NOTE: If the vehicle doesn't start within 6
seconds, let the jump starter cool for 3 minutes
before attempting to start the vehicle again or
you may damage the jump starter.
NOTE: During very cold conditions, the unit
may not start on the first attempt. We suggest
attempting to start a second or third time, as the
starting attempt will warm the internal battery
and improve your starting chances. Do not
attempt to start after four attempts – either the
unit does not have sufficient power to start the
vehicle or there is a more extensive problem
with the vehicle than simply a depleted battery.
5) When the vehicle is started, the smart cable/
clamp will show a solid blue LED and the
warning buzzer will beep.
6) Disconnect the clamp from the vehicle.
7) Disconnect the clamp from the jump starter.
3. CHARGING MOBILE DEVICES (SEE FIGURE
C)
1) Plug the USB charging cable into either the USB
1 or USB 2 charging port. You can charge up to 2
devices at a time.
2) Connect the charging cable to the mobile device
3) Press the power button to start charging
9
EN
Publicité
