Working Instructions; Maintenance Of The Magazine Attachment - Festool DWC 18-2500 Notice D'utilisation D'origine

9.4 Magazine attachment
The magazine attachment enables to work contin-
uously, without unnecessary delays.
Fitting the magazine attachment

At first remove the depth stopper [4-1] and bit,
bit holder [4-2] as specified in chapter 8.

Set the switch [1-4] into MAN position.

Push the long bit [8-1] completely to the hexag-
onal spindle opening [4-4].

Then fit the magazine attachment on the gear
box. Push the attachment until it engages in the
groove of the gear box.

The attachment can be mounted at 30° steps.
Removing the magazine attachment

Use power to carefully pull the magazine at-
tachment from the gear box.
Setting the screw length

Press button [9-1] to remove and insert the
depth stop [9-2] and set the required screw
length.
Read the set screw length on the depth stop sides
.
[9-3]
Inserting collated screw strips

Pull the collated screws [10-3] through the bot-
tom guiding of the attachment, then push the
strip through the second guiding until it engag-
es in the working position.
Pull the belt slightly to make sure that it is safe-
ly fitted.
Make sure that the first screw is in the screwing
axes – see figure [10].

Use the wheel [10-1] to set the required screw-
ing depth.

Turn to the right for inserting the screws deeper,
and to the left to screw to lower depth. The ac-
tual setting position is visible on the presetting
indicator [10-2].
Upon setting, set some screws for testing and use
the wheel [10-1] to adjust the depth, if required.
Each setting change complies with the stop shift o
± 0.1 mm.
 We recommend to screw in automatic mode –
see point 9.1 b).
Removing the collated screws

Pull upwards to remove the belt (figure [11]
or press the transport lever and concurrently
pull the belt downwards (figure [11]
10
– The magazine attachment must not be held in the
depth stop area as there are moving parts!
– Each screw adjustment must be completed. In-
terrupted fastening or releasing of the pressure
during adjustment can result in unsatisfactory
machine function.
– The collated screws and the magazine attach-
ment can only be replaced when the power tool is
turned off.
– Never use the magazine attachment in any other
way than specified in this instruction manual.
– Use only original screwing bits.
– Use only original collated screws.
– Always store the collated screws in original
packaging.
– Always work in right angle against the attached
board.
10.1
The attachment generally does not require any
maintenance. After long period use, we recom-
mend to clean with pressurized air.
The magazine attachment may be lubricated in the
area of the carriage guide (see picture [12b]).
Prior to cleaning, dismantle the attachment, as
specified above.
Prior to cleaning, remove the collated screws from
the attachment, as specified in the chapter 9.4 point
<Removing the collated screws>.
Pull the magazine attachment from the drywall
screwdriver.
Disassembly of the slides

Push the depth stopper [9-2] into the housing
until the arresting button [12-1] is at the level of
the sign for dismantling the slides [12-2] – see
figure [12a].

Press the arresting button [12-1] and concur-
rently remove the slides from the holder – see
figure [12b].

Press the button [9-1] and concurrently release
the depth stopper – see figure [12c].
Transport lever disassembly

Press the button [13-1] and concurrently pull it
out – see figure [13a].

Remove the released button [13-1] (figure
)
[13b]) with the transport lever [13-2] and the
spring [13-3] from the slides (figure [13c]).
).

Clean individual parts, replace defective or worn
parts, and assemble in the opposite sequence.

Working instructions

Maintenance of the magazine attach-
ment
DWC
GB
15