Technical Data - Kermi x-net Heißschneider connect Notice De Montage

of the unit and understand the ensuing risks. Children
shall not play with the appliance. Cleaning and user
maintenance may not be carried out by children wi-
thout supervision. Prevent manipulations by children or
immature people.
W Playing with the device is prohibited!
W The device may only be operated by qualified
specialists. Entrust all repairs to appropriate specialist
personnel.
PVC materials or those coated with PVC must not be
W
processed due to the dangerous vapours created du-
ring cutting.
W The room must be sufficiently ventilated to ensure that
vapours created during cutting are removed.
W Risk of burns! Do not touch the x-net Omega cutting
blade, it can reach temperatures of up to 500 °C!
W The hot cutting tip must not be put in contact with
heat-sensitive or flammable materials, as well as skin,
hair etc.
Danger of electric shock! Do not operate the unit if the
W
connection cable is damaged.
Disconnect the mains plug before making settings on
W
the device, change accessory parts or put the device
away.

Technical data

W Mains voltage
W Power input
Heating period
W
Protection type
W
Protection class
W
Working temperature
W
W Length of connecting cable
Danger!
Danger of death from electric shocks!
Protect the device from liquids and moisture. Other-
W
wise fires, short circuits, and fatal electric shocks can
be caused.
Commissioning
System parts (see figures, page 16)
A: x-net heat-cutter connect is designed for continuous
operation with its integrated fan.
B: x-net cutter carriage with x-net Omega cutting blade
C: x-net double cutting blades with two x-net Omega
cutting blades to cut two pipe layout ducts in one work
step
4
Make sure that the x-net heat-cutter connect plug is not
in the socket.
W Undo the four clamping screws found on the head of
the device using the enclosed hex socket key.
W Insert the x-net cutter carriage or x-net double cutter
carriage under the rectangular pressure plates until it
reaches the end stop.
W Retighten the clamping screws hand-tight again using
an Allen key.
Check the connection voltage on the name-
W
plate before inserting the plug into the socket.
Press the black switch on the housing to switch the device
on, and release it to switch it off. The x-net Omega cutting
blade will reach operating temperature after a heating pe-
riod of max. 5 seconds.
On the top of the x-net heat cutter connect you will find a
temperature control unit which can be adjusted in 16 steps
in accordance with the notches on the rotary knob.
If smoke appears while cutting, then the cut is being made
too slowly or the blade is too hot which can lead to an
oversized and uneven pipe duct. By reducing the tempe-
rature and occasionally releasing the black switch while
cutting, smoke formation is minimised and the cut is clean.
As soon as the cutting resistance increases, press the black
switch again.
230 V, 50 Hz IF the black switch is released approx. 3 – 5 cm away from
max. 330 W the end of the cut, then the x-net Omega cutting blade still
max. 5 seconds has sufficient residual heat to finish the cut and remains
IP 20 cleans and free of deposits. Never burn off excess residue
II on the hot x-net Omega cutting blades and this could cau-
-10 to +40 °C se them to overheat and become deformed.
6 m
Disposal
Recycle or dispose of the disused product, including
W
accessories and packaging, properly. Observe the local
regulations for disposal.
W The device should not be disposed of in household was-
te. Proper disposal ensures that environmental damage
and any health hazards are avoided.
Maintenance
Clean the device with a dry cloth only; do not use water or
solvent-based cleaning agents under any circumstances.
Clean the x-net Omega cutting blades when warm using
a brass brush.
The product is to be treated in
accordance with the WEEE Directive
2002/96/EC (Waste of Electrical and
Electronic Equipment) and the German
Electrical Equipment Act (ElektroG).