Functional Description; Intended Use; Product Features - Berner 102458 Manuel D'instructions

Masquer les pouces Voir aussi pour 102458:

Notice originale (137 pages)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

Table Des Matières

133

page de 133

/ 133
Matières
Table des Matières
Signets

Table des Matières

OBJ_BUCH-1172-001.book Page 10 Wednesday, January 13, 2010 1:51 PM

d) Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, break-

age of parts and any other condition that

may affect the power tool's operation. If

damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these instruc-

tions, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations different

from those intended could result in a hazardous

situation.

5) Service

a) Have your power tool serviced by a quali-

fied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Safety Warnings for Drills

Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory con-

tacting a "live" wire may make exposed metal parts

of the power tool "live" and could give the operator

an electric shock.

Use appropriate detectors to determine if

utility lines are hidden in the work area or

call the local utility company for assistance.

Contact with electric lines can lead to fire and

electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes prop-

erty damage or may cause an electric shock.

Switch off the power tool immediately when

the tool insert jams. Be prepared for high

reaction torque that can cause kickback. The

tool insert jams when:

— the power tool is subject to overload or

— it becomes wedged in the workpiece.

When working with the machine, always

hold it firmly with both hands and provide for

a secure stance. The power tool is guided more

secure with both hands.

10 | English

Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held more

secure than by hand.

Keep your workplace clean. Blends of materi-

als are particularly dangerous. Dust from light

alloys can burn or explode.

Always wait until the machine has come to a

complete stop before placing it down. The

tool insert can jam and lead to loss of control over

the power tool.

Never use the machine with a damaged

cable. Do not touch the damaged cable and

pull the mains plug when the cable is dam-

aged while working. Damaged cables increase

the risk of an electric shock.

Products sold in GB only: Your product is fitted

with an BS 1363/A approved electric plug with inter-

nal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it

should be cut off and an appropriate plug fitted in its

place by an authorised customer service agent. The

replacement plug should have the same fuse rating as

the original plug.

The severed plug must be disposed of to avoid a pos-

sible shock hazard and should never be inserted into

a mains socket elsewhere.

Products sold in AUS and NZ only: Use a residual

current device (RCD) with a rated residual current of

30 mA or less.