General Safety Rules; Work Area; Storage Temperature; Specific Safety Rules - Flexlite FLX3SA Manuel D'utilisateur

GENERAL SAFETY RULES

WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS

WORK AREA

 Keep your work area clean and well lit. Cluttered benches
and dark areas invite accidents.
 Working temperature. The worlight is designed to operate
in normal room temperature (21°C / 69.8°F). If it is use over
this room temperature, the LED lifetime will be reduced. If
temperature is over 37°C / 98.6°F, the LED light power will
be reduced and can cause permanent damage.
 Flexlite tripod is designed to be used in industrial
environnement, however, always protect your light system
against water and dust. Never immerse the system in water.
If the working area is moist and dusty, some particles will
stick on heatsink and reduce the performance. See
maintenance section to remove any dirt.
 Don't operate FLEXLITE under sunshine or near other heat
sources.
 It can't be used outside or under rain, moisture, snow, ...
DANGER!
Never connect/disconnect or use an external power
supply or charger in hazardous area.
Never connect or disconnect the connector on the
lighthead or any extension cord when the power is
ON.

SPECIFIC SAFETY RULES

 Know your worklight. Read operator's manual carefully.
Learn its applications and limitations, as well as the
specific potential hazards related to this worklight.
Following this rule will reduce the risk of electric shock, fire,
or serious injury.
 Lens and housing become hot during use:
 During or immediately after use, don't lay worklight flat
on lens surface or place lens area in contact with a plastic
or fabric covered surface.
 Handle worklight with care around any flammable surface.
 Do not use or permit use of worklight in bed or sleeping
bags. This worklight lens can melt fabric and could result
in burn injury.
 Do not disassemble your worklight.
 Do not permit children to use worklight unsupervised. It
is not a toy. The temperature of the light head will become
hot after being on for only a short period of time. This hot
temperature can cause burn injury if touched and can create
sufficient heat to melt some fabrics.
 Stay alert. Watch what you are doing and use common
sense. Do not rush.
SERVICE
 Worklight service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.

When servicing
replacement
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance Instructions may
create a risk of shock or injury

STORAGE TEMPERATURE

 Store worklight at room temperature between -35°C and
35°C (-31°F and 95°F) for best results.
 When transporting or temporarily storing in a vehicle,
temperature range should be greater than -35°C (-31°F) but
no more than 66°C (151°F).
 Storing worklight at temperatures greater than 76°C
(169°F) for extended periods of time (more than 2 hours)
may cause damage to worklight.
 These lights have not been investigated with regard to
duration or amount of light output and should not be
employed in lieu of Emergency Lighting and Power
Equipment where emergency lighting equipment is required.
 If wrapped or in contact with fabrics, the worklight lens
can produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the worklight lens to
come in contact with anything.
 Check damaged parts. Before further use of this worklight,
a part that is damaged should be carefully checked to
determine that it will operate properly and perform its
intended function. Do not use worklight if it does not
function properly.
 Do not abuse cord. Never use the cord to carry the
FLEXLITE. Do not pull cord rather than the plug when
disconnecting from receptacle. Damage to the cord could
occur and create an electric shock hazard. Replace damaged
cord immediately.
 Make sure cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving
parts or otherwise subjected to damage or stress. This will
reduce the risk of accidental falls, which could cause injury,
and damage to the cord, which could result in electric shock.
 Keep cord from heat to prevent damage to housing or
internal parts.
a worklight, use only
parts. Follow instructions
.
identical
in the
1