Manuels Connexes pour BIG ASS FANS LED Bay Light
Sommaire des Matières pour BIG ASS FANS LED Bay Light
- Page 1 INSTALLATION GUIDE LED Bay Light Luminaria de LED Manuel d’installation Guía de instalación Delta T LLC dba Big Ass Fans...
- Page 2 CAUTION: Risk of electric shock. Disconnect power before servicing. CAUTION: Install luminaire suspension cables correctly. Cables must be taut and secure. The light source contained in this fixture shall only be replaced by the manufacturer or his service agent or a similar qualified person. Suitable for damp locations.
- Page 3 READ AND SAVE THESE INSTRUCTIONS LIRE ET CONSERVER CES INSTRUCTIONS LEA Y CONSERVE ESTAS INSTRUCCIONES Conforms to UL Standard 1598, UL Standard 8750, CSA Standard C22.2 No. 250.0, and CSA Standard C22.2 No. 250.13 Conforme aux normes UL 1598, UL 8750, CSA C22.2 n 250.0, et CSA C22.2 n 250.13 Cumple con la norma UL 1598, la norma UL 8750, la norma CSA C22.2 No.
-
Page 4: Fixation Par Câbles
à quatre points pour empêcher le mouvement du luminaire. MISE EN GARDE : Big Ass Fans ne recommande pas l'installation du câble de montage autour d'une structure ou d'attaches présentant des arêtes vives, surtout en présence de vibrations ou de circulation d'air. - Page 5 Figure A Figura A Figure A1 Figure A2 Figure A3 Figura A1 Figura A2 Figura A3 ALL RIGHTS RESERVED. І TOUS DROITS RÉSERVÉS. І TODOS LOS DERECHOS RESERVADOS.
- Page 6 PENDANT MOUNT B1. Run the facility power wiring through customer-supplied 3/4 NPT conduit. Connect the wiring to the wires coming out of the conduit hub on top of the fixture, and then connect the conduit to the conduit hub. B2. Secure the other end of the conduit to the outlet box and connect the wiring. When finished, complete all Cable Mount steps as shown in Figure A.
- Page 7 Figure B Figura B Figure B2 Figura B2 Figure B1 Figura B1 ALL RIGHTS RESERVED. І TOUS DROITS RÉSERVÉS. І TODOS LOS DERECHOS RESERVADOS.
-
Page 8: Fixation Directe
DIRECT MOUNT Fig. C. Loosen the two captive screws on the bottom of the fixture and open the driver access door. Fig. D. Mount the fixture to ceiling joists using two suitable #8 or #10 mounting screws. If mounting to ceiling joists that are 16 in. (406 mm) apart, mount the screws in holes A and C or holes B and D in the top of the fixture. - Page 9 Figure C Figura C Figure D Figura D Hole D Trou D Hole C Orificio D Trou C Hole B Orificio C Hole A Trou B Trou A Orificio B Orificio A #8 or #10 #8 ou #10 #8 o #10 ALL RIGHTS RESERVED.
-
Page 10: Pivotement Du Module D'éclairage (Facultatif)
LIGHT MODULE ROTATION (OPTIONAL) 90° or 180° Rotation (Figure E) E1. While supporting the light module, use a 9/64 in. allen wrench to turn the screws on both ends of the fixture counterclockwise until they completely back out of the yellow end caps of the light module. E2. - Page 11 Figure E Figura E Figure E1 Figure E3 Figura E1 Figura E3 Figure E2 Figura E2 Figure F Figura F Figure F1 Figure F2 Figure F3 Figura F1 Figura F2 Figura F3 ALL RIGHTS RESERVED. І TOUS DROITS RÉSERVÉS. І TODOS LOS DERECHOS RESERVADOS.
-
Page 12: Power Wiring
POWER WIRING Refer to the input voltage rating marked on the fixture, and then wire according to the diagram and table below. Note: The dimming cable is optional. DIMMING FIXTURE POWER (1–10 VDC) L1 (BLACK IN US/CA/MX; BROWN OUTSIDE US/CA/MX) DIM+ DIM+ (VIOLET) -
Page 13: Câblage D'alimentation
CÂBLAGE D’ALIMENTATION Vérifiez la tension d’entrée assignée indiquée sur le luminaire, puis procédez au câblage conformément au schéma et au tableau ci-dessous. Remarque : le câble de gradation est facultatif. GRADATION LUMINAIRE ALIMENTATION (1–10 V CC) L1 (NOIR AUX ÉTATS-UNIS, AU CANADA, ET AU MEXIQUE ; MARRON DANS LES AUTRES PAYS) DIM+ DIM+... -
Page 14: Cableado Eléctrico
CABLEADO ELÉCTRICO Consulte la tensión de entrada nominal marcada en la luminaria y luego realice el cableado de acuerdo con el diagrama y la tabla que se incluyen a continuación. Nota: El cable de atenuación es opcional. Atenuación Alimentación LUMINARIA (1–10 VCC) L1 (NEGRO EN EE.UU./CANADÁ/ MÉXICO;... -
Page 15: Maintenance | Entretien | Mantenimiento
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by Big Ass Fans or a Big Ass Fans service agent or a similar qualified person in order to avoid a hazard. For assistance, please contact Customer Service. -
Page 16: Dépose Et Remplacement Des Lentilles
Removing and replacing the lenses The lenses are designed to be removable for cleaning or replacement. Handle lenses with care. Dépose et remplacement des lentilles Les lentilles sont conçues pour pouvoir être démontées afin d’être nettoyées ou remplacées. Les lentilles doivent être manipulées avec soin. Cómo retirar y reemplazar los lentes Los lentes están diseñados de modo que se puedan quitar para su limpieza o reemplazo. -
Page 17: Cleaning The Lenses
Cleaning the lenses Do not clean the fixture—especially the lenses—with scouring pads, alkaline cleaning substances, gasoline, thinner, benzene, heating oil, or polishing powder. Do not pressure wash or use a water hose to clean the fixture. Clean the lenses periodically to ensure optimal performance. Remove lenses and wipe with a clean, damp cloth. -
Page 18: Default Settings
OCCUPANCY SENSOR DÉTECTEUR DE PRÉSENCE | SENSOR DE OCUPACIÓN Default Settings High Mode......10 V Setpoint ......Disabled Low Mode ......Off Ramp Up ......Disabled Time Delay ......10 min Ramp Down ...... Disabled Cut Off ........ Disabled Photocell ......Disabled Sensitivity ...... - Page 19 CONTACT US NOUS CONTACTER | EN CONTACTO CON NOSOTROS United States Canada 2348 Innovation Drive 2180 Winston Park Drive Lexington, KY 40511 Oakville, Ontario L6H 5W1 Canada 877-244-3267 1 844-924-4277 Outside the U.S. (+1 859-233-1271) bigassfans.com bigassfans.com Singapore Australia 18 Tampines Industrial Crescent #06-07 35 French Street Singapore 528 605 Eagle Farm, Brisbane...
- Page 20 LTG-INST-263-MUL-01 REV C 01/21/2020 2251 Innovation Drive, Lexington, KY 40511 1 (877) BIG-FANS | WWW.BIGASSFANS.COM...