Publicité
Les langues disponibles
Les langues disponibles
QUICK USER GUIDE
D
S E
For remote control model # TXFM2WLCD
www.dsecanada.com
V05 April 2011
BUTTON
PRESS
1
0.5 sec
(I)
2
3 sec
(I)
3
0.5 sec
(II)
4
1.5 sec
(II)
5
0.5 sec
(III)
6
1.5 sec
(III)
7
5 sec
(III)
8
(II+III)
0.5 sec
+
(I+III)
9
+
0.5 sec
(I+IV)
10
0.5 sec
+
(IV)
11
0.5 sec
*Optional
Table for Programming Option (LCD Remote Only)
To Set The Clock
(III) for 5 sec and until the minutes icon starts to flash.
Step 1
Hold down button
Step 2
Adjust the minutes setting by tapping the button
ing. Once the desired minute has been set, tap button
Step 3
The Hrs icon will start to flash. Adjust the time with
(III) to move to AM / PM setting
Tap
Step 4
The AM/PM icon will start to flash. Adjust to AM by tapping the
Step 5
To exit the Clock mode, tap button
sec.
To Set Timer Start Mode
To program a specified Start time
(III) for 5 sec and until the minutes icon starts to flash.
Step 1
Hold down button
(III) button 3 times until the the icon TIMER STARTS MODE starts to flash
Step 2
Press
Step 3
The Minute icon will start to flash. Adjust the minute by tapping
(III) to move to Hr or AM / PM and repeat the same procedure to adjust the desired
Tapping
function.
(III) 1 times or it will automatically exit within 15 sec
Step 4
To exit, tap
To cancel Start time
(III) button for 5 sec until the Minutes icon starts to flash
Step 1
Hold down
(III) button 3 times, the Timer Start Mode will start flashing
Step 2
Press
(III) button 1.5 seconds will cancel Start time mode
Step 3
Press
FUNCTION
Lock / Arm
Panic
Unlock / Disarm ( Stop Panic )
Trunk release * or Sliding doors 1 * ( AUX 1 )
Lock / Unlock Silently
Sliding doors 2 * ( AUX 2 )
Programming menu
(see below Table for programming option)
Trunk release if equipped with Sliding doors *
Enable Mute/Vibration mode.
To disable repeat the same
Block all buttons
Start engine. Repeat to Stop
(I) for increasing and
(II) for decreas-
(III) to move to hours
(I) and
(II) accordingly.
(I) button and PM the
(III) 4 times or it will automatically exit within 15
(I) or
(II) button accordingly.
Cold Start Timer
(every 2, 3 or 4 hrs for 6, 10, 15 or 20 minutes when installed)
I
(I) and
(II) buttons at the same time to enable this function, parking lights
1 - Press
II
will flash 2 times to confirm for 2 hrs
III
2 - Repeat same for 3 hrs and for 4 hrs
3 - To Cancel this feature, start the vehicle with the transmitter or with the key
IV
Important: Do not use this feature when the vehicle is parked in a closed area
Pit stop
Running mode — Without key and with alarm (Applicable only for automatic car).
If you want to keep the engine running & the accessories working (heater, air conditioner) for a short
time when you're not in the vehicle, proceed as follow:
Before shut the engine off:
(IV) button
1 - Press once
2 - Remove the key from the ignition. The engine will stay running
3 - Open and close the door.
engine will keep running for a maximum of 20 minutes
Important: This feature does not function is the brake pedal is depre
Starter Kill
(optional and selectable in Auto or Manual mode)
Car starter will not work when the starter kill is in function. After disarming, the system will re-arm auto-
matically within 60 seconds (in Auto mode) except if the car is started prior to the 60 seconds. To disarm,
(II) button of the transmitter and start the vehicle
press once the
Valet Mode / Override
In the case of lost or malfunction of the transmitter, use this mode to bypass or override the alarm or the
starter kill function.
a) turn the key to the Run (On) position
b) immediately within 6 sec :
1 - Press and release the override button. You will hear 1 chirp and /or one parking flash to
confirm (if installed)
2 - OR Push and release the brake pedal at least or more than 6 times if that option is chosen
c) LED will stay On for 5 sec and Off for 5 sec continuously
Start with the key as usual. System is temporary suspended
To reset the system, repeat step a and b. You will hear 2 chirps and / or 2 parking flash to confirm. The
LED will start flashing slowly and the system is back in the normal operation
The remote starter for manual transmission does not monitor the position of the gear shift. It
requires the user of the vehicle equipped with this remote starter for manual transmission to ac-
tivate the parking brake or the hand brake and leave the gear shift in the Neutral Position At All
Time before leaving the vehicle even when he or she does not intend to remote start the vehicle.
The Manufacturer will not be liable for any consequences resulted from Misuse, Negligence or
(II) button.
Improper installation.
Reservation Mode for Manual Transmission Only
The following sequences must be performed in order to remote start the vehicle equipped with a manual
transmission (applicable for Turbo as well):
1 - While the engine is running, leave the gear shift in Neutral, apply the parking brake, remove foot from
brake pedal
2 - Press momentarily the
unlock
❉
3 - Remove the key, engine will remain running
4 - Exit the vehicle, close the door, engine will then shut off with 1 chirp (if installed), door will lock & alarm
is engaged automatically after 6 seconds (if installed). The vehicle can now be safely remote started
Remark:
However, the remote start function will be cancelled if a door is opened after step 4 has been complete.
Once cancelled, to re-initiate the remote start function:
- Start the vehicle with the key
- Repeat above step 1 to 4
Important When trying to remote start the vehicle and the car parking lights flashes 4 times without
starting, repeat steps 1 to 4
Automatic Transmission
(I) your vehicle with your transmitter (if installed) or with your key. The
Manual Transmission
WARNING
!
!
button of the transmitter, parking light will turn and stay On, doors will
ssed
Publicité
