Changing Cooking Control Method - Hatco Rapide Cuisine IRNGCD Série Manuel D'installation Et D'utilisation

English
Advanced Programming Mode
Advanced Programming Mode increases the versatility of
the Induction Range by allowing preset, three-stage cooking
programs (menu items) to be created. Four screens are
available on the Control Display in Advanced Programming
Mode: Power Control, Temperature Control (Fahrenheit or
Celsius), Menu, and Settings.
S S
Power Control Temperature
Screen Control Screen
The Settings screen in Advanced Programming Mode includes
all of the options from Standard Mode as well as the following
additions:
TEMP UNIT = Used to change temperature unit of measure
PROGRAM = Used to create custom menu items
Refer to "Programming Menu Items" in this section to create
custom menu items.
Startup
1. Before turning on the unit each day, clean the glass cooking
surface using an appropriate cleaning wipe, damp paper
towel, or a damp cloth. CAUTION! Wipe up all spills and
splashes immediately. Make sure unit is dry before
using. Do not allow liquid to run into air inlet filter on
bottom of unit.
NOTE: The unit can be turned off at any time by pushing the
Control Knob.
NOTE: The cooling fan in the unit will not start until the unit gets
hot. Once the fan turns on, it will run until the unit cools.
2. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
• A Welcome screen will appear on the Control Display for
a few seconds, then the display will go blank.
3. Place an induction-ready pan on the unit. The Induction
Range will not operate without a pan centered inside the
cooking zone pattern on the glass cooking surface.
4. Push the appropriate Control Knob
to start the Induction Range.
• The blue Power Control Screen
appears showing a bar graph
and a percentage of power
setting. The Induction Range is
now operating in Power Control.
See "Changing Cooking Control Method" for information
on cooking in Temperature Control.
• If the unit is in Advanced Programming Mode, refer to
"Cooking with Menu Items" in this section to cook using
programmed menu items.
NOTE: The pan icon on the display will flash when a pan is not
being heated or when no pan is on the glass cooking
surface. The icon will remain solid when a compatible
pan is on the cooking surface and being heated. If the
Power setting is at "0" or the Fahrenheit Temperature
setting is below 79°F, no pan icon will appear.
Form No. IRNGCDM-1020
S
Menu Settings
Screen Screen
S
Power Control—Standard
5. Turn the Control Knob to adjust the Power setting to the
desired percentage.
• Turn the Control Knob clockwise to increase the setting.
Turn the Control Knob counterclockwise to decrease the
setting.
• Most cooking in Power Control will be done at a setting
of 50% or less. Start with a lower setting because the unit
gets hot quickly. Make adjustments as necessary.
NOTE: Heat generation will stop automatically whenever a pan
is removed from the glass cooking surface. The unit will
hold the current setting for three minutes. If the pan is
placed back on the unit within the three minutes, the unit
will resume cooking at the current setting. After three
minutes, the Control Display will go blank and the unit
will shut off.
Shutdown
1. Push the appropriate Control Knob to turn off the Induction
Range. The Control Display will go blank.
NOTE: Heat generation will stop automatically whenever a pan
is removed from the glass cooking surface.

Changing Cooking Control Method

Two cooking control methods are available in both operation
modes on the Induction Range: Power Control and Temperature
Control. To change control methods:
1. Touch the Button on the control panel to toggle through
the cooking control methods. The screens appear in the
order shown below (the Settings Screen that appears is
used for changing unit operation mode and settings).
S
Power Control—
Standard
2. Turn the Control Knob to adjust the setting on the desired
screen.
• Turn the Control Knob clockwise to increase the setting.
Turn the Control Knob counterclockwise to decrease the
setting.
NOTE: Settings in Power Control do not correspond to the
temperature setting in Temperature Control.
General Setting Information
Hatco recommends adjusting the Power or Temperature
settings up or down while cooking to find the best setting for
a particular pan, amount of food, and heating desired. Once a
good setting has been determined, use this setting in the future
for cooking similar batches of the same size, in the same pan.
Save these settings as a menu item in Advanced Programming
Mode for quick and easy repeat cooking.
Power Control Information
Power Control supplies a continuous amount of heat to the
pan, similar to the operation of a gas or electric burner. The
Power setting is based on the amount of heat wanted in the
pan. Observe the cooking of the food in the pan and make
adjustments to the Power setting as necessary.
13
OPERATION
S
Temperature Control—
Standard