Hudora 14012 Instructions De Montage Et Mode D'emploi page 3

INSTrUcTIoNS oN ASSemBLY AND USe
EN
coNGrATULATIoNS oN
PUrchASING ThIS ProDUcT!
Please read these instructions carefully. The instructions are an integral
component of the product. Therefore, please store them and the packa-
ging carefully in case questions arise in the future. Please always include
these instructions when giving the product to a third party. This product
must be assembled by an adult. This product is not designed for indus-
trial use. The use of the product requires certain capabilities and skills.
Always adjust according to the age of the user and use for the purpose it
has been designed for.
TechNIcAL SPecIFIcATIoNS
Item: Free Style Scooter XS-12, XS-13
Stunt Scooter XR-23, XR-24
Item number: 14012, 14013, 14023, 14024
Dimensions: 64 x 43 x 82,5 cm
Item weight: 3,5 kg
Maximum user weight: 100 kg
If you have assembly problems or would like further information on the
product, we have all you need and more at http://www.hudora.de/.
coNTeNTS
1 x Scooter (in two parts)
2 x Allen wrench M5
1 x Manual
Other items included are meant to facilitate safe transportation and are
not required for the installation and use of the product.
SAFeTY INSTrUcTIoNS
• The scooter is only intended for use by one person.
• Only use the scooter on surfaces that are suitable for it, i.e. those which
are flat, clean, dry, and use the scooter where possible away from other
road users. Avoid sloping ground. The brakes may become hot if the
scooter has been used for a while! They shouldn't be touched until they
have cooled down.
• Always be considerate of others.
• Wear suitable protective clothing for your own safety. Never use the
scooter without a helmet and hand/wrist, elbow and knee pads. Never
use the scooter without shoes!
• Before you start. Ensure that all fasteners and locking parts are intact
and tight; the functioning of the self-locking threads can slacken after
repeated loosening and tightening of the fasteners. Check especially for
the correct alignment and fastening of the steering set-up.
• Do not use the scooter at twilight, at night or in poor visibility. Do not
use it on roads or thoroughfares or on slopes or hills. Avoid being in the
proximity of stairs and open water.
• The scooter is not a vehicle in the sense of the road traffic regulations!
It is intended for use on footpaths.
SeT-UP INSTrUcTIoNS
Loosen the locking screws on the handlebar clamp as far as possible so
that you can slide the clamp over the end of the handlebar. Now slide
the handlebar as far as it will go onto the fork. The handlebars must be
aligned in a straight manner. Tightly screw on the locking screws of the
clamp. Make sure that the handlebar remains straight. For disassembly
of the scooter, carry out the described Installation steps but however in
the reverse order.
All images are examples of the design.
USAGe INSTrUcTIoNS
NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten minutes. Par-
ticular care should be taken during this stage.
USAGE INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just as with
well-known children's scooters. Braking is no problem either - simply
step on the friction brake over the back wheel (mudguard).
mAINTeNANce AND STorAGe
Use a dry or damp cloth only to clean the product; do not use special
cleaning agents! Check the product for damage or traces of wear and tear
before and after each use. Do not make any structural changes. For your
own safety, please use original spare parts only. These can be sourced
from HUDORA. If parts become damaged or if sharp edges or corners
should develop, the product may not be used any more. If in any doubt,
please contact our service team (http://www.hudora.de/). Store the pro-
duct in a safe place where it is protected from the elements, cannot be
damaged, and cannot injure anyone.
WHEEL CHANGE
Replacement wheels are available as accessories from http://www.hu-
dora.de and should be replaced when they are worn down. However, it is
usually advisable to change the bearings when the wheels are changed.
To change the wheels, loosen the axle fitting with two size 5 Allen keys
and take the wheels off the axle. A screwdriver or Allen key can be used
to push the bearings out of the wheel to use them in the new wheel. Put
the bearings into the new wheel with the bolt spacer and mount them to
the frame with the axle screws. Make sure the axle has been screwed on
tightly before starting again!
BEARINGS
Your scooter is equipped with precision ball bearings which were filled
with lubrication at high pressure during manufacture. For this reason, the
wheels only run easily and quickly when there is a load on the scooter.
The bearings are maintenance free. If a bearing should fail, it should be
replaced completely. Bearings are available as accessories from http://
www.hudora.de.
DISPoSAL ADVIce
At the end of the product's life, please dispose of it at an appropriate coll-
ection point provided in your area. Local waste management companies
will be able to answer your questions on this.
SerVIce
We make every effort to deliver faultless products. If faults do arise how-
ever, we put just as much effort into rectifying them. Therefore, you can
find numerous information on the product, replacement parts, solutions
to problems and lost assembly manuals at http://www.hudora.de/a/Z3T.
3/8