Adjusting The Pc Image; Pc Compatibility Chart; Setting Audio Input - Sharp Aquos LC-46LE540U Mode D'emploi

Using a PC
Example
Menu
System
Options
System Options
View Option
AQUOS LINK Setup
Input Terminal Setting
O ti L k O t
1
Press MENU to display the MENU screen, and then
press c / d to select "System Options".
2
Press a / b to select "Input Terminal Setting", and
then press ENTER.
3
Press a / b to select "PC input" or "Audio Select",
and then press ENTER.
4
Press a / b to select a specifi c adjustment item,
and then press ENTER to set each item.
5
Press a / b (or c / d ) to select or adjust the desired
setting, and then press ENTER.

Adjusting the PC Image

Auto Sync. (for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. start and "Auto adjusting ..." displays.
No: This function does not work.
• "Auto Sync." may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing "Auto Sync.".
• Be sure to connect the PC to the TV and switch it on before
starting "Auto Sync.".
Fine Sync.
Ordinarily you can easily adjust the picture as necessary
to change image position using "Auto Sync.". In some
cases, however, manual adjustment is needed to
optimize the image.
H-Pos.: Centers the image by moving it to the left or right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image fl ickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image fl ickers.
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.

PC Compatibility Chart

It is necessary to set the PC correctly to display XGA
and WXGA signal.
Resolution
720 x 400
640 x 480
VGA
SVGA
800 x 600
XGA 1024 x 768
SXGA 1280 x 1024
SXGA+ 1400 x 1050
UXGA 1600 x 1200
1080p 1920 x 1080
VGA and XGA are registered trademarks of International
Business Machines Corp.

Setting Audio Input

Audio Select
This function sets the terminal to output the computer
audio.
The adjustment items vary depending on the input
source. Select the input source corresponding to the
terminal connected to the PC and then adjust the
desired item.
PC IN
Video: Select this when the TV and PC are connected
using an analog RGB cable and the audio is not input.
Video+Audio: Select this when the TV and PC are
connected using an analog RGB cable and the audio is
input via a Ø 3.5 mm stereo minijack.
HDMI IN
Auto: Audio selected automatic the default setting is
"Auto".
HDMI(Digital): Select this when the TV and PC are
connected using an HDMI-certifi ed cable and audio is
input via the same cable.
HDMI+Analog: Select this when the TV and PC are
connected using a DVI-HDMI conversion cable and the
audio is input via a Ø 3.5 mm stereo minijack.
• When "Audio Select" is set to "HDMI(Digital)", sound will
not be produced if you use only an HDMI-certifi ed cable to
connect HDMI-compatible equipment. To produce sound,
you should make an analog audio connection.
• If you want to connect HDMI-compatible equipment
using only an HDMI-certifi ed cable, set "Audio Select" to
"HDMI(Digital)".
Horizontal Vertical VESA
Frequency Frequency Standard
31.5 kHz 70 Hz
31.5 kHz 60 Hz
37.5 kHz 75 Hz
37.9 kHz 60 Hz
48.1 kHz 72 Hz
46.9 kHz 75 Hz
48.4 kHz 60 Hz
56.5 kHz 70 Hz
60.0 kHz 75 Hz
64.0 kHz 60 Hz
65.3 kHz 60 Hz
75.0 kHz 60 Hz
67.5 kHz 60 Hz
O
O
O
O
O
O
O
O
O
O
O
47