Publicité
Liens rapides
NADIA
User Manual
Guide de l'utilisateur
Pressure Balance
Shower Panel
Colonne de douche
à pression balancée
SPB 9817BN
SPB 9817BL
ANTICALCAIRE
NON-CLOGGING
DO NOT RETURN THIS PRODUCT TO STORE, CONTACT US - Monday to Friday, 9 a.m. to 4:30 p.m. EST. We're there if you need help.
For assistance with product assembly, to report damaged or missing parts, or for any other information about this product, please call our toll-free number.
NE RETOURNEZ PAS CE PRODUIT AU MAGASIN, CONTACTEZ-NOUS - Du lundi au vendredi, 9 h à 16 h 30 HNE.
Nous sommes là si vous avez besoin d'aide. Pour obtenir de l'aide pour l'assemblage de votre produit, pour signaler des pièces endommagées,
manquantes, ou pour toute autre information concernant ce produit, veuillez composer notre numéro sans frais.
1 844 666-0155 • question@dimex360.com
2020-10
Publicité
Manuels Connexes pour Akuaplus NADIA SPB 9817BN
Sommaire des Matières pour Akuaplus NADIA SPB 9817BN
- Page 1 NADIA User Manual Guide de l’utilisateur Pressure Balance Shower Panel Colonne de douche à pression balancée SPB 9817BN SPB 9817BL ANTICALCAIRE NON-CLOGGING DO NOT RETURN THIS PRODUCT TO STORE, CONTACT US - Monday to Friday, 9 a.m. to 4:30 p.m. EST. We’re there if you need help. For assistance with product assembly, to report damaged or missing parts, or for any other information about this product, please call our toll-free number.
- Page 2 été utilisé de façon non recommandée ou s’il a fait l’objet de négligence. akuaplus®...
- Page 3 #22 HJ40 #16 KK64 64 mm...
- Page 4 Parts list/Liste de pièces N°/No. Description N°/No. Description 1 Shower panel Colonne de douche 21 Retaining brass gasket Rondelle de retenue en laiton 2 Bamboo Bambou 22 Pressure balance cartridge Cartouche à pression équilibré 3 Shower arm in brass Bras de douche en laiton 23 Finishing flange Bride de finition 4 Flange...
- Page 5 Recommended preparation of your wall / Préparation recommandée de votre mur 2x6 in. Piece of wood reinforcement Pièce de renforcement fait de 2x6 po Not included Non inclus 1/2” NPT You will need to reinforce your wall with 2 x 6 inches pieces of wood as shown (2), to do this, place the shower panel against the wall at the desired height (1) to measure and mark the position of the top bracket for the 2 x 6 (A), bottom bracket position for the 2 x 6 (C), and the 2 x 6 position of the 90˚drop ear elbow (B).
- Page 6 Place and mark the upper shower panel bracket (F), measure the distance between the both shower panel brackets (H) in order to place and mark at the right position the support of the bottom (G). Placez et marquez le support de la colonne de douche du haut (F), /- 41 po/in.
- Page 8 Put on the impurity filter washer (A). Apply teflon (B) tape to the pipe nipples. Install the 90° connectors firmly on the pipe nipples and tighten with ¼ turn with an adjustable wrench. Connect the hoses to the shower panel while making sure they are not twisted. Install the shower panel on the wall brackets. It is recommended not to apply silicone seal around the panel.
- Page 9 Reverse this process when putting the cartridges in place. Effectuez le processus inverse pour remettre les cartouches en place. You may need to clean your cartridges if they accumulate limescale. Brush them under running water with a toothbrush, let them soak for a minimum of eight hours in undiluted white vinegar, brush again and rinse under running water.
- Page 10 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION Cold water and hot water are Bad connection of hot and cold water supplies Invert the hot and cold water supplies tube reversed Check whether the filter washers, the non-return valve or the Complete or partial blockage of the hot water supply cartridges are free of any impurities Water is not hot enought Your water heater does not give you hot enough water...