Configuration; Pl1/Pf1 Pl2/Pf2 Pl3/Pf3 Pl4/Pf4 - Bticino U0085C Mode D'emploi

GB
LED
SELF-LEARNING MODE
This mode can associate a single command to any remote control key. With just one receiver up to 16 commands can be associated to a remote
control (using the 16-channel remote control 4482/16).
To allow programming or cancelling a key the two-way switch on the back must be in the "padlock open" position.
To associate a different command to each of the remote control channels, the procedure is the following:
1) press the pin pushbutton for 3 seconds: the led shines steadily;
2) within 20 seconds press the key on the remote control for the channel to be programmed: the led will start to flash, indicating that the programming
mode has been activated;
3) set the command to be associated to the remote control key by means of the commands and/or the corresponding actuator: the led shines
steadily;
4) at this point points 2 and 3 can be repeated for all the keys, even for a key which has already been associated if it is to be changed;
5) press the pin key to quit the programming: the led goes out;
To cancel the programming of one of the remote control channels the procedure is the following:
1) press the pin pushbutton for at least 8 seconds: after 3 seconds the led shines steadily; after another 5 seconds it goes out; release the key
within 4 seconds: the led shines steadily;
2) within 20 seconds press the key on the remote control for the channel to be cancelled: the led flashes quickly for about 4 seconds, confirming
cancellation;
3) from this moment the cancelled key will not activate any command until it is reprogrammed.
To cancel the programming of all the remote control channels at the same time, press the pin pushbutton for about 12 seconds: after 3 seconds
the led shines steadily; after another 5 seconds it goes out; after another 4 seconds it flashes quickly for about 4 seconds, confirming that all the
programming has been cancelled.
Commands which the receiver can learn:
a. Automation
- ON/OFF actuator (short press for cyclical ON/OFF operation and long press for adjustment)
- Timed ON
- Flash
- Rolling shutters UP and DOWN (up-down to end of stroke)
- Lock/Unlock actuator
- Call scenario
b. Video door entry system
- Command door lock (also in session)
- Command staircase lights
c. Sound system
- Amplifier ON + volume setting UP; (always in Follow-me mode)
- Amplifier OFF + volume setting DOWN
- Source cycling
- Change station/tune
d. Auxiliary channels
- Light auxiliary ON/OFF (cyclical ON/OFF operation)
- Rolling shutter auxiliary UP/DOWN (up-down to end of stroke)
SCENARIO MODULE COMMAND F420
This mode is only used if the system has a scenario module.
It can create, cancel or edit the scenarios in the scenario module and use the
remote control to call them. The procedure can save up to 16 scenarios using
all 16 channels of the 16-channel remote control. The table below shows the
correspondence between the number of the scenario saved in the scenario
module and the remote control channels:

CONFIGURATION

PL1/PF1
PL2/PF2
PL3/PF3
PL4/PF4
Insert the address of the scenario module to be commanded in A and PL1.
The scenario module must be in the configuration with self-learning enabled
(press the self-learning key so that its led is green, if it is red the self-learning is
not enabled) and the two-way switch on the back of the IR receiver must be in
the "padlock open" position.
Front view
Receiving lens
Programming/reset
pushbutton
CONFIGURATION
0÷9
A
1÷9
0
0
0
6
M
operation
mode
Selector switch to
enable the
programming
0÷9
A
PL1/PF1 1÷9
0
PL2/PF2
0
PL3/PF3
PL4/PF4 0
0
M
Scenario module
scenario number
Scenario 1
Scenario 2
Scenario 3
Scenario 4
Scenario 5
Scenario 6
Scenario 7
Scenario 8
Scenario 9
Scenario 10
Scenario 11
Scenario 12
Scenario 13
Scenario 14
Scenario 15
Scenario 16
Rear view
A
addresses
PL1/PF1
PL2/PF2
PL3/PF3
PL4/PF4
M
16-channel remote 7-channel remote
control
4482/16
Ch1
Ch2
Ch3
Ch4
Ch5
Ch6
Ch7
Ch8
Ch9
Ch10
Ch11
Ch12
Ch13
Ch14
Ch15
Ch16
7
control
4482/7
Ch1
Ch2
Ch3
Ch4
Ch5
Ch6
Ch7