Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
Weight capacity
per arm ................................................................................
total ......................................................................................
Maximum height .....................................................................
Mount screw ...........................................................................
Size folded ..............................................................................
Total lenght .............................................................................
Maximum weight on each ballast hook...................................
Total maximum weight on ballast hooks .................................
Weight according EPTA-Procedure 01/2014 ..........................
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS TRIPOD
This is a tool support. Do not use for any other purpose than
supporting tools not exceeding a maximum weight of 9 kg
(4.5 kg per arm).
Before using a tool, be sure all adjustments are secure.
Use the tripod in a dry, indoor place protected from wet
conditions.
When transporting the tripod in a vehicle, securely tie it
down to prevent movement and possible damage.
Maximum weight placed on tripod must be 9 kg or less.
Do not use the tripod as a seat or stand.
Check to make sure tripod does not rock, slide or move prior
to use.
Put the tripod on a fi rm level surface where there is plenty of
room to handle and properly support the tool.
Do not mount tools that exceed the maximum weight
capacity of the tripod or cause the tripod to tip excessively.
Just because the tool can be attached to your tripod, it does
not assure safe operation.
Do not use this product if it is not completely assembled or if
any parts appear to be missing or damaged. Use of a
product that is not properly and completely assembled or
with damaged or missing parts could result in serious
personal injury.
Do not attempt to modify this product or create accessories
or attachments not recommended for use with this product.
Any such alteration or modifcation is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
When adjusting the height of the tripod, hold the upper or
middle tube with one hand and unlock the clamp with the
other. If not held properly, the top portion of the tripod and
any tool mounted to the tripod could descend rapidly and
cause serious personal injury or property damage.
Keep everyone - helpers, bystanders, children, and animals
- a safe distance from an extended tripod. Serious personal
injury or property damage could occur if the tool is tipped.
Unless you are adjusting or mounting tools to the tripod,
keep a minimum distance of 4572 mm away from the
product.
To ensure proper balance and reduce the risk of a tipping
hazard, center the weight of two or more mounted tools over
one of the tripod legs.
12
ENGLISH
TRIPOD
LUS-210X
LUS-210X
.................................4,5 kg
.................................4,5 kg
.................................9,0 kg
.................................9,0 kg
..............................2100 mm
..............................2100 mm
............................... 1/4"
............................... 1/4"
............ 882 x 198 x 155 mm
............ 882 x 198 x 155 mm
.................................2,1 m
.................................2,1 m
.................................6,8 kg
.................................6,8 kg
...............................13,6 kg
...............................13,6 kg
.................................3,9 kg
.................................3,9 kg
SPECIFIED CONDITIONS OF USE
The Tripod is intended to use for the mounting of a
maximum of 2 AEG battery lights.
Do not use this product in any other way as stated for
normal use.
ADJUSTING THE LOCK CLAMPS
The lock clamps may become loose and move over time. If
necesary, close and reposition the clamp then use a 3 mm
hex key to tighten the cam and secure the clamp in place.
Open and close the clamp to ensure it is functioning
properly.
MAINTENANCE
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before
starting the machine.
Open - Lock.
Total maximum weight on ballast hooks
When adjusting the height of the tripod,
hold the upper or middle tube with one
hand and unlock the clamp with the
other. If not held properly, the top
portion of the tripod and any tool
mounted to the tripod could descend
rapidly and cause serious personal
injury or property damage.
Dry indor use only. To ensure proper
balance and reduce the risk of a tipping
hazard, center the weight of two or
more mounted tools over one of the
tripod legs.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
13
Publicité
