EINHELL CC-JS 8 Mode D'emploi page 15

4. Technical data
Jump start power bank
Li-Po battery: ....................................... 27.75 Wh
Charging time approx. ................................... 3 hr
USB d.c. voltage outlet: ................... 5 V max. 2 A
Jump starting current: .........................................
................................. 200 A (5 sec) / 400 A (max.)
Ambient temperature for jump starting: ...............
..................................................... - 15°C - + 40°C
Charger
Nominal input voltage: ....... 100-240 V ~50/60 Hz
Nominal output voltage: ........................ 15 V DC
Nominal output current: .................................. 1 A
5. Before starting the equipment
5.1 Charging the jump start power bank with
the supplied charger
The following applies to the charger:
This equipment can be used by children of 8 ye-
ars and older and by people with limited physical,
sensory or mental capacities or those with no ex-
perience and knowledge if they are supervised or
have received instruction in how to use the equip-
ment safely and understand the dangers which
result from such use. Children are not allowed
to play with the equipment. Unless supervised,
children are not allowed to clean the equipment
and carry out user-level maintenance work.
Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to the supply voltage.
Important! Pull out the power plug before making
adjustments to the equipment. Charge the equip-
ment only with the charger supplied.
Observe the enclosed safety information with de-
tailed information about charging.
The outlets must not be used while charging is in
progress.
•
Connect the supplied charger (Fig. 2a / Item
10) to the „15V 1A input" charging jack (Fig. 1
/ Item 2) on the equipment.
•
Plug the charger into the socket outlet and
the battery will be charged. The LED (Fig. 1/
Item 6) shine (flash) during charging and in-
dicate the charging status. When charging is
Anl_CC_JS_8_SPK7.indb 15 Anl_CC_JS_8_SPK7.indb 15
GB
finished, all the LED shine.
•
The time it takes to fully recharge an empty
battery is approximately 3 hours. The tem-
perature of the battery pack may rise slightly
during the charging operation. This is normal.
5.2 Charging the jump start power bank with
the 12 V cigarette lighter cable
Charging should be performed only while driving,
as the vehicle's battery is discharged in the pro-
cess. Place the equipment in a suitable location
where it cannot move in response to an abrupt
change in speed and/or direction.
•
Connect the supplied 12 V cigarette lighter
cable (Fig. 2b / Item 11) to the „15V 1A input"
charging jack (Fig. 1 / Item 2) on the equip-
ment.
•
Plug the 12 V connector into a suitable 12 V
cigarette lighter socket.
5.3 Battery capacity indicator
Press the ON/OFF button (Fig. 1/Item 5) briefl y.
The LED for the battery capacity indicator (Fig. 1
/ Item 6) light up. The number of LED that are lit
indicate the current charge level of the integrated
Li-Po battery.
100% charged = 4 LED steady on
<25% charged = 1 LED fl ashing light
6. LED lamp
Caution! Do not look into the light beam.
•
Press the ON/OFF button for 3 seconds – the
LED lamp (Fig. 1 / Item 4) will be permanently
lit.
•
Press the ON/OFF button again – the LED
lamp will be lit as a „strobe light".
•
Press the ON/OFF button again – the LED
lamp will be lit as an „SOS" Morse code sig-
nal lamp.
•
Press the button again to switch the LED
lamp off again.
- 15 -
05.12.2016 08:52:24 05.12.2016 08:52:24