Eurotops Master 01 Mode D'emploi page 12

R 8828 / CR-8828P
The status appears in following sequence with display shown as :
Alarm wake to buzzer is set with Alarm 1 Buzzer indicator (11) and Alarm time is flashing on
the display.
Alarm wake to radio is set with Alarm 1 Radio indicator (12) and Alarm time is flashing on the
display.
Alarm off is set with no indicator is on and current time shown on LED
5 seconds after the desired status is chosen, the display will stop flashing and change to
show the current time. Please make sure the indicator for the selected status (buzzer or
radio) is ON, or no indicator is on in case if you choose to turn off the alarm.
When you set the Alarm 2 time, follow the above step 2 to 5 by using the ALARM 2 button
(2) instead of ALARM 1 button (1). Subsequently, the wake to buzzer status of alarm time 2
will be indicated by Alarm 2 Buzzer indicator (14).
The wake to radio status of alarm time 2 will be indicated by Alarm 2 Radio indicator (15).
The buzzer sound of Alarm 1 is in different tone with the buzzer sound of Alarm 2, so it is
easy for user to distinguish.
When the Alarm is turned on, either :
Press ON/OFF button (3) or Alarm 1 button (1) once to switch off the alarm 1.
Press ON/OFF button (3) or Alarm 2 button (2) once to switch off the alarm 2.
The alarm indicator is still on, implying the alarm function is still activated and
turned on again after 24 hours.
Press the SNOOZE button (9), the alarm sounds will stop temporarily for 9 minutes and will
sound again after. [See SNOOZE SETTING below]
If no button is pressed after the alarm sounds, the alarm will keep turned on and then turned
off in 1 hour after the alarm time.
To disable the alarm setting, press ALARM 1 button (1) or ALARM 2 button (2) until their
indicators (radio or buzzer) disappear on the display.
Notes
The ALARM 1 (or 2) indicator flashes in the display when the alarm sounds.
If a later alarm starts to sound when the earlier alarm still sounds, then the later alarm takes
priority.
If a later alarm sounds when the earlier alarm is under SNOOZE period, then the later alarm
takes priority and will cancel the SNOOZE function of the earlier alarm automatically.
If the same time is set for both alarm (ALARM 1 or 2). The ALARM 2 takes priority.
9) SNOOZE SETTING
Once the alarm is activated, the snooze function can be used to stop the alarm temporary
for about 9 minutes and then alarm will sound again.
Once alarm ( either Alarm 1 or Alarm 2 ) sounds, press the SNOOZE button (9), the buzzer or
radio alarm sounds will stop and will sound again after 9 minutes. The SNOOZE function can
maintain valid within 1 hour from the set alarm time.
During the time when SNOOZE function is activated, the alarm indicator will flash.
To switch off the SNOOZE function, press ON/OFF button (3). You can then see the alarm
indicator stop flashing, and the alarm will not sound again after the snooze period elapse.
10) SETTING THE SLEEP TIMER
The sleep function allows the radio to play in blocks of 10, 20, 30, 40, 50, 60, 70, 80, or 90
minutes before turning off automatically, then you can enjoy falling asleep when listening
the radio.
Turn on the radio.
Press the SLEEP button (9), then the LED shows 90 ( for 90 minutes ).
Press the SLEEP button (9) repeatedly until the display shows the desired SLEEP time period.
The time period is shown on the display in sequence as 90 > 80 > 70 > 60 > 50 > 40 > 30 > 20
> 10 > OFF.
In 2 seconds after the desired SLEEP period is chosen, the display will change to show the
current time, and the radio will play for the SLEEP time duration you have set and then be
turned off automatically.
Press the SLEEP button (9) again during SLEEP mode, the LED will show
the remaining time of the SLEEP period, and the SLEEP time can be set again
by following above step 3 & 4.
To switch off the SLEEP function during the SLEEP mode, follow above step 3 until "OFF"
appears on the LED, then the SLEEP function is cancelled. The LED jumps back to show the
radio frequency and the radio will keep turned on until being turned off manually.
11) SETTING THE SLEEP TIMER AND ALARM TOGETHER
1) If you want to set the SLEEP TIMER function and Alarm function together, you
must follow the ALARM SETTING procedure to set the alarm first.
2) Turn on the radio, then follow the step 2 & 3 of SETTING THE SLEEP TIMER.
Consequently, the radio will be turned off automatically after the SLEEP time elapse, and
then wake you up at your set alarm time.
C. CARE AND MAINTENANCE
Clean the product only with a dry lint-free cloth.
D. FEATURES
Power Source : 220V~50Hz
Radio Frequency : AM: 522 ~ 1620 KHz
FM: 87.5 ~ 108 MHz
: 50 mm, 8 Ω, 0.5W
Speaker
Power consumption : 5 W
DC Battery for back up : 3V, 2 x AAA size batteries ( not included )
* Specifications are subject to change without notice.