Eurotops Master 01 Mode D'emploi page 11

R 8828 / CR-8828P
pressing of TU- button (8) can tune down by 0.1 MHz and each pressing of TU+ button (7)
can tune up by 0.1 MHz.
Auto Scanning: Press and hold either of the 2 tuning button, TU- button (8) or TU+ (7) for
more than 1 second and auto scan will be performed. Scanning will stop automatically until
a clear radio signal is found. Repeat the same procedure by using the same button until your
desired station is found.
* To stop auto scanning, press any button once.
Note : In some area where the radio signal is not strong enough, the scanning process may
not be able to stop automatically in the desired station. In such case, please use the Manual
Tuning method to tune the desired station. This happens more probably when tuning the
radio in MW band.
To turn off the radio, press and hold ON/OFF button (3) for more than 1 second until the
radio is turned off and the LED shows the time.
Note 1: The current station (either MW or FM) and also the current volume level
will be memorized at the time when the radio is turned off. Once you turn on
the radio again, the memorized station will broadcast with the memorized
volume level.
Note 2: For the best FM reception, extend the FM antenna wire to its full
length and vary the direction to capture the strongest signal. Do not connect
the FM antenna wire to an outdoor antenna.
Note 3: For AM reception, a ferrite-bar antenna is built-in. Since this antenna is direction
oriented, turn the unit to a direction at which the reception becomes optimal.
4) PRESETTING YOUR FAVOURITE STATION
You can preset up to 10 stations in 10 memories for each band. These 10 memories
are indicated as preset numbers P01, P02, P03, P04, P05, P06, P07, P08, P09 and P10.
During the radio operation mode, follow step 4 in "Operating the radio" and tune the radio
into the station that you wish to preset.
Press and hold the SET button (4) for more than 1 second until the last memorised preset
number appears and flashes.
You can then choose the preset number that you want to memorize this station by pressing
MEMORY- (5) to step down the sequence, or by pressing MEMORY+ (6) to step up the
sequence.
Once the preset number is chosen, it will keep flashing for 5 seconds. Press SET button (4)
once within these 5 seconds, then the tuned station will be memorized in this chosen preset
number and the LED will stop flashing and change to show the frequency.
If the SET button (4) is not pressed within these 5 seconds, then the LED will jump back to
show frequency, and the memory storing does not succeed.
If the chosen preset number is already memorized with a station, the above procedure will
allow the newly tuned station to supersede the originally memorized station.
In following the above steps, you can memorize your 10 most favorite stations
of each band into the 10 preset numbers.
5) TUNING INTO A PRESET STATION
When the radio is on (either MW or FM), press SET button (4) or MEMORY+ (6) once, then
the radio will be tuned to station stored in the preset number next to the last loaded preset
number.
Press MEMORY- button (5) once, the radio will be tuned to station stored in the preset
number previous to the last loaded preset number.
You can choose your desired preset memory by pressing MEMORY- button (5) to step down
the sequence or MEMORY+ button (6) to step up the sequence.
After the preset number is chosen, it will be shown for 2 seconds, then the LED will change
back to show the radio frequency.
Important Note: Please do NOT hold (press continuously) the SET button (4) in this stage. If
this is done by mistake, the unit will enter into the mode of presetting the station, with the
preset number flashing. In such case, do not press any button until the LED stop flashing.
Otherwise, your set memory may easily be disturbed by your wrong operation procedure.
6) TIME SETTING
When the unit is first plugged into the AC mains, "0:00" will appear and flash on the display.
Press HOUR button (8) for hour setting.
Press MINUTE button (7) for minute setting.
After setting to the correct time, either press SET button (4) once, or just leave 5 seconds,
then the display stop flashing, and the clock will start run from the set time.
To adjust the current time, first switch off the radio. Press and hold SET button (4) for 1
second until the display flashes, then follow the same steps as point 2, 3 & 4 above to set the
new time.
7) DUAL ALARM FUNCTION
This product allows the user to set to dual alarm function. Each alarm function can be set
independently, either wake to radio, or wake to buzzer. When any one alarm is set waking
to radio, please be reminded to select the desired band, station and volume level before
turning off the radio.
8) ALARM SETTING
To set the alarm time, the radio must be turned off.
Press ALARM 1 button (1) once, the alarm time and either Alarm 1 Buzzer indicator (11) or
Alarm 1 Radio indicator (12) is flashing.
Press HOUR button (8) for selecting hour. Press MINUTE button (7) for selecting minutes.
After setting the desired alarm time, either press ALARM 1 button (1) again,
or simply wait for 5 seconds, then the display will return to the current time
and the set alarm time is confirmed.
Now press ALARM 1 button (1) repeatedly to choose the alarm function status.