Location Requirements - KENMORE ELITE HE5t Steam 110.4778 Série Guide D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See "Drain
System."
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale in the steamer
and other areas of the washer. Over time the buildup of lime
scale may clog the steamer, which will reduce steamer
efficiency and performance. Excessive buildup of scale may
lead to the need for steamer replacement or repair.
A level floor with a maximum slope of 1" (2.5 cm) under
entire washer. Installing the washer on soft floor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
Installation clearances
The location must be large enough to allow the washer door
to be fully opened.
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
Washer Dimensions
51"
(129.5 cm)
6

Location Requirements

27"
(68.6 cm)
38"
(96.5 cm)
31¹⁄₂"
(80.0 cm)
Recommended installation spacing for custom
undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
39" min.
(99.0 cm)
1"
(2.5 cm)
Recommended installation spacing for recessed or
closet installation, with or without a pedestal
The dimensions shown are for the recommended spacing.
Recessed area or closet installation
34"
(86.4 cm)
1"
31¹⁄₂"
4"
(2.5 cm)
(80 cm)
(10.2 cm)
A
A. Side view - closet or confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recessed or closet installation - Washer on pedestal
1"
27"
(2.5 cm)
(68.6 cm)
A
A. Recessed area
B. Side view - closet or confined area
1"
27"
(2.5 cm)
(68.6 cm)
3"
(7.6 cm)
2
48 in.
*
2
(310 cm
)
2
24 in.
*
3"
2
(155 cm
)
(7.6 cm)
B
18" min.
(45.7 cm)
1"
1"
31¹⁄₂"
4"
(2.5 cm)
(2.5 cm)
(80 cm)
(10.2 cm)
B

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

He5t steam 110.4779 série

Table des Matières