Jilong avenli 17726 Série Mode D'emploi page 6

RP2-21-GB
Slide combined beams into sleeve,the hole on the beams should face outwards.
Step5. INSTALL HORIZONTAL BEAM AND L-TUBE
Plastic Sleeve
Step6. INSTALL HORIZONTAL BEAM AND U-TUBES
Find the one side holes on the horizontal beam.Place and lock the T-joints into the holes.Ensure they are fully connected
PART5-FILL THE POOL WITH WATER
WARNING:
Do not leave pool unattended while filling with water.
WARNING:
If more than 1~2 inches of water collects on any one side before you
start filling in the center.The pool is not level enough, and must be corrected! You
shall pull out the drain plug, release the water completely, disassemble the pool
completely,locate the pool on a plane surface, repeat set up instructiion.
WARNING:
DO NOT OVERFILL as this could cause the pool to collapse.In times of
heavy rainfall you may need to empty some of the water to ensure the level is correct.
90%
10
1. Make sure the drain fitting is plugged securely and the cap
is in place. Start filling the pool with water. After about 1-inch of
water is on the bottom, stop filling and smooth wrinkles out of the
bottom of the pool. Pull the outer wall out from the top edge, all
around the bottom of the pool, so that it fills evenly.
2. Contineue filling the pool until water level.
PART6-WINTERISING AND LONG-TERM STORAGE
WARNING:
Do not let your children stand at downfold and face the water outlet
during the drainage. The water current may sweep your children.
WARNING:
Pool should be stored at places where is cool and dry, with no sharp
object surroued, or no heavy objects lying above, which may cause damage to the
pool.
Step1.
If you have a filter pump, make sure that the electricity source to the filter pump has been disconnected.
Step2.
Check to ensure that the out drain plug is firmly inserted on the inside of the pool.
Step3.
Attach your garden hose to the drainage valve connector, and placing the other end of the hose in an area where the
water can drain safely, such as a storm drain or street gutter. Remember that because water always finds its own level, the end
of the hose must be lower in elevation than the pool to ensure complete drainage.
Step4.
If you have a filter pump, insert the stopper into the inlet and outlet fix tures, on inside of pool, and then disconnect
the filter pump hoses.
Step5.
Attach the drainage valve connector to the drain outlet by turning connector in a clockwise direction.
Step6.
Open the out drain plug on the inside of the pool and the water will begin to drain immediately.
Step7.
Disconnect the hose and drainage valve connector when finished.
Step8.
Replace the out drain plug on the inside of the pool.
Step9.
Be sure that the pool liner is completely dry before folding the pool for long-term storage. Leaving the pool exposed to
sunlight for a few hours will clean and speed the drying process and make it easier to fold the pool for storage. (Never attempt
to fold or stow a pool that is not completely dry as this could lead to a proliferation of mold or mildew build-up during the time
the pool is in storage.)
Step10.
Remember, proper off-season storage is critical to protect your investment in your pool.(espeically in winter) Once
drained and dry, your pool should be carefully folded and wrapped in a ground cloth (if available) or other similar protective
tarp-like material. The pool and all applicable accessories such as the pump, cover, ground cloth, ladder, hoses, clamps, and
hardware should be kept together and stored indoors, in a reasonably warm, dry and weatherproof location.
FOLDING INSTRUCTION
Before folding, it's better to dry all parts and pool completely by lying them in the sun
for one hour or so.(PIC.1). And then, spread some talcum powder to prevent the vinyl
from sticking together.
Step1.
Please fold the protrusion sides inside to gain rectangle shape.(PIC.2).
Step2.
Fold each half of the rectangle to gain a smaller rectangle shape.(PIC.3).
Step3.
Fold each ends backwards. (PIC.4).
Step4.
Fold the rest ends together to create an ultimate rectangle one.(PIC.5).
TIPS1.
Please remove air inside to make the folded pool thin and flat during each folding.
TIPS2.
The original packing can be used for storage.
PIC.1 PIC.2
PIC.5
RP2-21-GB
PIC.3 PIC.4
11