Replaying A Message Sequence; Time-Controlled Replay; Creating A Schedule - Monacor PA-1120DMT Mode D'emploi

6) Use the button UP or DN to select the storage
M1 M6
location ( –
age]) for the first program step
7) Press the button START/ STOP (14). Use the
button UP or DN to select the storage location
for the second program step
8) Proceed in the same way to store all messages
to be replayed in the desired order. Finally,
press the button START/ STOP and then the
button ENTER or wait for approx. 30 seconds
until programming will be automatically finished.
Pressing the button ENTER will delete the
program step most recently shown, delete the
subsequent program steps and exit program-
ming. Then the replay mode will be selected
again ( chapter 6.4.2).
Note: When program step 20 has been entered, wait for
approx. 30 seconds to exit programming; pressing the but-
ton ENTER will delete all program steps.

6.4.2 Replaying a message sequence

1) Press the button MENU (10). The display will
show:
Mode Set
Time
2) Press the button UP (12) or DN (11) repeatedly
RECALL
until appears on the lower display
line.
3) Press the button ENTER (6). The display will
now show:
RECALL
PGM Play
4) Press the button ENTER. The display will show,
for example:
PGM Play
P01 M6
5) Press the button START/ STOP (14). The replay
will start and the display will now show:
PGM Play
P01 ....
The programmed messages will be replayed
one after the other and the indication of the pro-
gram step replayed will change accordingly:
P01 P02 P03
, , , ...
6) To stop the replay, press the button START/
STOP again.
7) When the replay is started via the button
REPEAT/ STOP (13), the replay will stop after
each message. To start the subsequent mes-
sage of the program, press the button again.
Pressing the button while a message is
being replayed will stop the message; to replay
the next message, press the button again.
V01 V20
or – ["voice" stor-
P01
.
P02
.

6.5 Time-controlled replay

The stored messages may automatically and regu-
larly be replayed at specific times; for each week-
day, up to 20 different times for replay can be
defined. The schedule of a weekday can be copied
to other weekdays, if required.

6.5.1 Creating a schedule

1) Press the button MENU (10). The display will
show:
Mode Set
Time
2) Press the button UP (12) so that
appear on the lower display line.
3) Press the button ENTER (6). The display will
now show:
Choose
Week Set
4) Press the button ENTER. The display will show:
Program
Mon
5) Press the button UP or DN (11) to set the week-
day desired ( chapter 5.3).
6) Press the button ENTER. The display will show,
for example:
CH:01 01
16:10 21
(program location 1, replay once,
start time 16:10 h, message M1)
Note: The numbers 01 – 20 indicate the messages
Voice01 – 20; the numbers 21 – 26 indicate the mes-
sages M1 – M6.
7) Use the button UP or DN to search for a free
CH:
program location "
then press the button ENTER. The display will
show:
Program
Change
Press the button ENTER.
8) Use the buttons UP, DN and ENTER to enter
the values desired for the hour (
Min:
minute ( ), the message (
M:1 6
or – ) and the number of repeats (
01 09
– = replayed 1 to 9 times,
continuously). The display will then show a
"summary" of the values entered, for example:
CH:03 01
16:10 21
(program location 3, replayed once,
start time 16:10 h, message M1)
Note: The numbers 01 – 20 indicate the messages
Voice01 – 20; the numbers 21 – 26 indicate the mes-
sages M1 – M6.
Program
will
-- --:-- --"
XX / and
Hour:
), the
Voice:01 20
–
Rep :
00
= repeated
GB
21